u-boot.git/drivers/misc/Makefile, branch v2024.07

drivers: misc: Fixes: Rename CONFIG_SPL_SOCFPGA_SEC_REG to CONFIG_SPL_SOCFPGA_DT_REG

2024-04-15T03:16:06+00:00

Commit 3f190c55a4211215914126b74357344342329943
("drivers: misc: Add socfpga_dtreg driver for Intel SoCFPGA")

This commit rename CONFIG_SPL_SOCFPGA_SEC_REG to CONFIG_SPL_SOCFPGA_DT_REG
in Makefile.

Signed-off-by: Wan Yee Lau

gpio: turris_omnia_mcu: Add support for system power off via sysreset

2024-04-04T08:45:27+00:00

Add support for system power off via UCLASS_SYSRESET. Newer versions of
Turris Omnia MCU firmware can power off the board (MCU will disable
almost all voltage regulators and go into low power mode).

Move the MCU driver into drivers/misc and register it under UCLASS_MISC.
The sysreset and gpio device are bound as child devices of the MCU device.

Signed-off-by: Marek Behún 
Reviewed-by: Stefan Roese

drivers: misc: Add socfpga_dtreg driver for Intel SoCFPGA

2024-03-18T03:05:09+00:00

Add socfpga_dtreg driver enablement for Intel SoCFPGA.

Signed-off-by: Wan Yee Lau 
Reviewed-by: Tien Fong Chee

smbios: copy QEMU tables

2024-01-16T22:05:29+00:00

QEMU provides SMBIOS tables with detailed information. We should not try to
replicate them in U-Boot.

If we want to inform about U-Boot, we can add a Firmware Inventory
Information (type 45) table in future.

Signed-off-by: Heinrich Schuchardt 
Reviewed-by: Simon Glass

serial: msm-geni: don't rely on parent misc device

2024-01-16T12:26:52+00:00

commit 1b15483deb3f ("misc: add Qualcomm GENI SE QUP device driver")
introduced support for platform-specific oversampling values, necessary
to configure the UART clocks on all platforms at runtime. However it
relies in probing a parent device. Despite the DM_FLAG_PRE_RELOC flag,
this is not done consistently during boot.

Instead, take another approach by relying on ofnode_ helpers to read the
serial engine base address and do the read directly. This fixes early
UART on boards with a non-default oversampling rate.

Signed-off-by: Caleb Connolly

acpi: carve out qfw_acpi.c

2024-01-07T20:49:15+00:00

Move the code related to copying tables from QEMU to a separate code
module.

Signed-off-by: Heinrich Schuchardt 
Reviewed-by: Tom Rini 
Reviewed-by: Simon Glass 
Reviewed-by: Ilias Apalodimas

rockchip: Port IO-domain driver for RK3568 from linux

2023-10-07T08:49:41+00:00

Port the Rockchip IO-domain driver for RK3568 from linux.

The driver auto probe after bind to configure IO-domain based on the
regulator voltage. Compared to the linux driver this driver is not
notified about regulator voltage changes and only configure IO-domain
based on the initial voltage autoset by the regulator.

It is not recommended to enable MMC_IO_VOLTAGE or the mmc signal voltage
and IO-domain may end up out of sync.

Based on the linux commit 28b05a64e47c ("soc: rockchip: io-domain: add
rk3568 support").

Signed-off-by: Jonas Karlman 
Reviewed-by: Simon Glass 
Reviewed-by: Kever Yang

imx: use generic name ele(EdgeLockSecure Enclave)

2023-07-13T09:29:40+00:00

Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.

Signed-off-by: Peng Fan

misc: add Qualcomm GENI SE QUP device driver

2023-05-02T18:23:58+00:00

This change adds a Qualcomm GENI SE QUP device driver as a wrapper for
actually enabled and used serial devices found on a board.

At the moment the driver is pretty simple, its intention is to populate
childred devices and provide I/O mem read interface to them as clients,
this is needed for GENI UART driver to set up a proper clock divider
and provide the actually asked baud rate.

Signed-off-by: Vladimir Zapolskiy 
Reviewed-by: Konrad Dybcio

misc: Drop mc9sdz60 driver

2023-02-07T19:33:48+00:00

Drop this unused driver.

Signed-off-by: Simon Glass