u-boot.git/drivers/misc, branch v2015.04-rc2

dm: Expand and complete Kconfig in drivers/

2015-02-12T17:35:33+00:00

Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.

Signed-off-by: Simon Glass 
Reviewed-by: Masahiro Yamada

dm: cros_ec: Convert cros_ec_i2c over to driver model

2015-01-30T00:10:01+00:00

Move this driver to use driver model and update the snow configuration to
match.

Signed-off-by: Simon Glass

dm: cros_ec_spi: Remove old pre-driver-model code

2015-01-30T00:09:57+00:00

This is no-longer needed since all platforms use SPI for cros_ec.

Signed-off-by: Simon Glass

dm: cros_ec: Don't require protocol 3 support

2015-01-30T00:09:57+00:00

I2C is now deprecated on ARM platforms and there are no devices that use it
with the v3 protocol. We can't require v3 support if we want to support I2C.
Adjust the error handling to suit.

Signed-off-by: Simon Glass

dm: spi: Move slave details to child platdata

2015-01-30T00:09:56+00:00

At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.

However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.

Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.

Signed-off-by: Simon Glass

dm: cros_ec: Remove use of fdtdec GPIO support

2015-01-30T00:09:51+00:00

These functions are going away, so use the new uclass support instead.

Signed-off-by: Simon Glass

i2c_eeprom: include to fix build error

2015-01-06T00:45:15+00:00

drivers/misc/i2c_eeprom.c fails to build unless CONFIG_FIT_SIGNATURE
is defined.

  CC      drivers/misc/i2c_eeprom.o
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:15:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:15:10: note: each undeclared identifier
is reported only once for each function it appears in
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_write':
drivers/misc/i2c_eeprom.c:21:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:22:1: warning: control reaches end of
non-void function [-Wreturn-type]
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:16:1: warning: control reaches end of
non-void function [-Wreturn-type]
make[2]: *** [drivers/misc/i2c_eeprom.o] Error 1
make[1]: *** [drivers/misc] Error 2
make: *** [drivers] Error 2

By the way, Sandbox (enabling CONFIG_FIT_SIGNATURE) is luckily
working depending on it.
Sandbox includes include/asm-generic/errno.h
            from include/errno.h
            from include/u-boot/rsa-checksum.h
            from include/image.h
            from include/common.h
            from drivers/misc/i2c_eeprom.c

Signed-off-by: Masahiro Yamada 
Acked-by: Simon Glass

x86: Add a simple superio driver for SMSC LPC47M

2014-12-14T05:32:05+00:00

On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.

Signed-off-by: Bin Meng 
Acked-by: Simon Glass

dm: Add a simple EEPROM driver

2014-12-11T20:18:43+00:00

There seem to be a few EEPROM drivers around - perhaps we should have a
single standard one? This simple driver is used for sandbox testing, but
could be pressed into more active service.

Signed-off-by: Simon Glass 
Acked-by: Heiko Schocher 
Reviewed-by: Masahiro Yamada

dm: i2c: Add an I2C EEPROM simulator

2014-12-11T20:18:42+00:00

To enable testing of I2C, add a simple I2C EEPROM simulator for sandbox.
It supports reading and writing from a small data store.

Signed-off-by: Simon Glass 
Acked-by: Heiko Schocher 
Reviewed-by: Masahiro Yamada