The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu.  Use hierarchic menu for each category.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>

This is not needed with driver mode. Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add a driver to support the special LDO access used by spring. This is a
custom method in the cros_ec protocol - it does not use an I2C
pass-through.

There are two implementation choices:

1. Write a special LDO driver which can talk across the EC. Duplicate all
the logic from TPS65090 for retrying when the LDO fails to come up.

2. Write a special I2C bus driver which pretends to be a TPS65090 and
transfers reads and writes using the LDO message.

Either is distasteful. The latter method is chosen since it results in less
code duplication and a fairly simple (30-line) implementation of the core
logic.

The crosec 'ldo' subcommand could be removed (since i2c md/mw will work
instead) but is retained as a convenience.

Signed-off-by: Simon Glass <sjg@chromium.org>

The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.

With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.

Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.

For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.

Signed-off-by: Simon Glass <sjg@chromium.org>

Only 2 frequencies are supported. The current driver implementation does
not always use the 2 last configured blink frequencies. This patch
fixes this problem. So that the last two entered frequencies are
active.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tom Rini <trini@konsulko.com>

Add a test to confirm that we can access system controllers and find their
driver data.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move sandbox over to use the reset uclass for reset, instead of a direct
call to do_reset(). This allows us to add tests.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add drivers for sandbox. One can only perform a warm reset (which does
nothing). The other can perform a cold reset or a power reset (the
latter will quit U-Boot). These can be used for testing the reset uclass.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add a new reset_walk_halt() function to cause a reset and then halt on
failure. The reset_walk() function returns an error code.

This is needed for testing since otherwise U-Boot will halt in the middle
of a test.

Signed-off-by: Simon Glass <sjg@chromium.org>

It is common for system reset to be available at multiple levels in modern
hardware. For example, an SoC may provide a reset option, and a board may
provide its own reset for reasons of security or thoroughness. It is useful
to be able to model this hardware without hard-coding the behaviour in the
SoC or board. Also there is a distinction sometimes between resetting just
the CPU (leaving GPIO state alone) and resetting all the PMICs, just cutting
power.

To achieve this, add a simple system reset uclass. It allows multiple devices
to provide reset functionality and provides a way to walk through them,
requesting a particular reset type until is it provided.

Signed-off-by: Simon Glass <sjg@chromium.org>