Both FS_LOADER and SPL_FS_LOADER have the same menu prompt.
To avoid confusion, make prompt for SPL_FS_LOADER different.

Signed-off-by: Alexander Gendin <agendin@matrox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

- Fix some issues Coverity has reported, update MAINTAINERS file,
  another bootstd fix, typo fix in error message, gitignore fix and
  update TI's URL in many places.

Replace instances of http://www.ti.com with https://www.ti.com

Signed-off-by: Nishanth Menon <nm@ti.com>

Extend the otp driver to read rv1126 otp. This driver code was
adapted from the Rockchip BSP stack.

Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

on Peach-pi console every key press is echoed with message
'cros_ec_command: Returned status 1'

this is not proper fix, just hack to disable this message

Signed-off-by: Milan P. Stanić <mps@arvanta.net>
Reviewed-by: Simon Glass <sjg@chromium.org>

Calculate the maximum length of the buffer when writing
across the page boundary. If the buffer length (len)
exceeds the page boundary (pagesize), split it. Use this
length instead of comparing the length with the pagesize,
because if the write start address (offset) is not at the
beginning of a page and the page_offset + len is greater
than the page boundary (pagesize), the write operation
would overflow the current page and the behaviour can be
undefined (e.g. at24).

Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>

Similar change was done by commit b4c2c151b14b ("Kconfig: Remove all
default n/no options") and again sync is required.

default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com> # tegra
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Angelo Dureghello <angelo@kernel-space.org>

To avoid thermal burn out, program thermal shutdown
value in VTM (Voltage and Thermal Manager) IP.

Part of Linux kernel driver (drivers/thermal/k3_j72xx_bandgap.c)
is ported from kernel 6.6-rc1, which sets thermal shutdown values.

Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Neha Francis <n-francis@ti.com>

In current vexpress_config_probe code, it sets the uclass private data
directly. This will cause one compilation error:
drivers/misc/vexpress_config.c:114:27: error: lvalue required as left operand of assignment
  114 |  dev_get_uclass_priv(dev) = priv;
      |                           ^

In this patch we set the uclass private data through struct member
.priv_auto, and this compilation error disappears.

Signed-off-by: Wei Chen <wei.chen@arm.com>
Signed-off-by: Qi Feng <qi.feng@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

The ST M24C32-D behaves as a regular M24C32, except for the -D variant
which uses up another I2C address for Additional Write lockable page.
This page is 32 Bytes long and can contain additional data. Add entry
for it, so users can describe that page in DT. Note that users still
have to describe the main M24C32 area separately as that is on separate
I2C address from this page.

From Linux kernel commit:
4791146e9055 ("eeprom: at24: add ST M24C32-D Additional Write lockable page support")

Signed-off-by: Marek Vasut <marex@denx.de>