u-boot.git/drivers/mmc/Makefile, branch v2011.09

ftsdc010: add support of ftsdc010 mmc controller

2011-09-04T23:03:02+00:00

Faraday FTSDC010 controller is a SD/MMC controller for SoC chip.

Signed-off-by: Macpaul Lin

OMAP3: Remove legacy mmc driver

2011-09-04T09:36:18+00:00

Now that all platforms have been migrated to the new MMC driver, remove
the old one.

Signed-off-by: Tom Rini 
Signed-off-by: Sandeep Paulraj

mmc: sh_mmcif: add support for Renesas MMCIF

2011-07-16T01:29:21+00:00

Some Renesas SuperH have MMCIF module. This driver supports it.

Signed-off-by: Yoshihiro Shimoda 
Acked-by: Andy Fleming

MMC: add marvell sdhci driver

2011-07-16T01:29:19+00:00

This could support both armada100 and pantheon serial in the mainline,
while this driver also be tested to support upcoming mg, mmp2 and mmp3
hardware.

Signed-off-by: Lei Wen 
Acked-by: Andy Fleming

MMC: add sdhci generic framework

2011-07-16T01:29:18+00:00

Nowdays, there are plenty of mmc driver in uboot adopt the sd standard
host design, aka as sdhci. It is better to centralize the common logic
together to better maintenance.

Signed-off-by: Lei Wen 
Acked-by: Andy Fleming

mmc: Tegra2: SD/MMC driver for Seaboard - eMMC on SDMMC4, SDIO on SDMMC3

2011-07-16T01:28:56+00:00

Signed-off-by: Tom Warren 
Acked-by: Andy Fleming

MMC: Add support for PL180 ARM mmc device

2011-04-29T08:20:01+00:00

Add support for the ARM PrimeCell MultiMedia Interface - PL180.
Ported from original device driver written by ST-Ericsson.

Signed-off-by: Matt Waddel

mmc: add generic mmc spi driver

2011-04-13T11:35:22+00:00

This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.

The crc checksum on data packet is enabled with the def,

There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.

Signed-off-by: Thomas Chou 
Signed-off-by: Andy Fleming

Davinci MMCSD Support

2011-02-01T23:54:44+00:00

Added support for MMC/SD cards for Davinci.  This feature is enabled by
CONFIG_DAVINCI_MMC and is dependant on CONFIG_MMC and CONFIG_GENERIC_MMC
options. This is tested on DM355 and DM365 EVMs with both the available mmc
controllers.

Signed-off-by: Alagu Sankar 
Signed-off-by: Sandeep Paulraj

Switch from archive libraries to partial linking

2010-11-17T20:02:18+00:00

Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier