u-boot.git/drivers/mmc/Makefile, branch v2015.01

sort drivers/mmc/Makefile

2014-11-07T21:27:04Z

Sort drivers/mmc makefile, as requested by wd. Signed-off-by: Pavel Machek Acked-by: Chin Liang See

mmc: s3c: Add SD driver

2014-08-01T16:24:34Z

Implement SD driver for the S3C24xx family. This implementation is currently only capable of using the PIO transfers, DMA is not supported. Signed-off-by: Marek Vasut Cc: Kyungmin Park Cc: Lukasz Majewski Cc: Minkyu Kang Cc: Pantelis Antoniou Cc: Vladimir Zapolskiy Acked-by: Pantelis Antoniou

ARM: kirkwood: add mvsdio driver

2014-08-01T15:44:56Z

This patch add Marvell kirkwood MVSDIO/MMC driver and enable it for Sheevaplugs and OpenRD boards. Signed-off-by: Gerald Kerma Reviewed-by: Stefan Roese Acked-by: Pantelis Antoniou

sunxi: mmc support

2014-05-25T14:26:43Z

On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote: > > + case 1: > > +#if CONFIG_MMC1_PG > Are you sure that this is correct and shouldn't be: > > +#ifdef CONFIG_MMC1_PG > > ? It's "correct" in so far as it works (the boards.cfg config stuff #defines things to 1), but I think you are right that it isn't the preferred style. But... > A quick scan through this patch series shows that this define > is not set at all. Perhaps its outdated? Or is it used to support > some other sunxi SoC? Not sure, perhaps it should be removed for > now. ...I had thought that it was to support some other board which wasn't being upstreamed right now, so eventually useful and harmless for now, but I've just checked and it isn't actually used by any of the boards in u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it. Rather than resend the entire series, here is v5.1 of this patch. > Other than this please add my: > > Reviewed-by: Stefan Roese Thanks! 8<--------------------------------- >From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001 From: Ian Campbell Date: Fri, 7 Mar 2014 04:29:39 +0000 Subject: [PATCH v5.1 7/8] sunxi: mmc support This adds support for the MMC controller on the Allwinner A20 (sun7i) processor. Signed-off-by: Henrik Nordstrom Signed-off-by: Luke Leighton Signed-off-by: Oliver Schinagl Signed-off-by: Wills Wang Signed-off-by: Ian Campbell Reviewed-by: Marek Vasut Reviewed-by: Stefan Roese Cc: Tom Cubie Cc: Aaron Maoye Cc: Pantelis Antoniou Reviewed-by: Tom Rini

eMMC: add support for operations in RPMB partition

2014-05-23T08:52:51Z

This patch adds functions for read, write and authentication key programming for the Replay Protected Memory Block partition in the eMMC. Acked-by: Pantelis Antoniou Signed-off-by: Pierre Aubert

mmc: kona: Add Kona mmc driver

2014-02-22T18:30:41Z

Add support for the Kona SDHCI found on Broadcom mobile SoCs. Signed-off-by: Darwin Rambo Reviewed-by: Steve Rae Reviewed-by: Tim Kryger

socfpga/dwmmc: Adding DesignWare MMC driver support for SOCFPGA

2014-01-09T09:53:55Z

To add the DesignWare MMC driver support for Altera SOCFPGA. It required information such as clocks and bus width from platform specific files (SOCFPGA handoff files) Signed-off-by: Chin Liang See Cc: Rajeshwari Shinde Cc: Jaehoon Chung Cc: Pantelis Antoniou Cc: Wolfgang Denk Acked-by: Pantelis Antoniou

mmc: add Faraday FTSDC021 SDHCI controller support

2013-12-08T12:23:05Z

Faraday FTSDC021 is a controller which is compliant with SDHCI v3.0, SDIO v2.0 and MMC v4.3. However this driver is only verified with SD memory cards. Signed-off-by: Kuo-Jung Su Acked-by: Pantelis Antoniou CC: Andy Fleming

drivers: convert makefiles to Kbuild style

2013-10-31T17:26:01Z

Signed-off-by: Masahiro Yamada

mmc: don't support write & erase for SPL builds

2013-09-20T15:58:55Z

For SPL builds this is just dead code since we'll only need to read. Eliminating it results in a significant size reduction for the SPL binary, which may be critical for certain platforms where the binary size is highly constrained. Signed-off-by: Paul Burton Acked-by: Pantelis Antoniou