u-boot.git/drivers/mtd/spi, branch v2019.04

Convert CONFIG_SF_DEFAULT_* to Kconfig

2019-03-25T21:36:53Z

This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: Patrick Delaunay

mtd: spi: Add lightweight SPI flash stack for SPL

2019-02-07T10:03:21Z

Add a tiny SPI flash stack that just supports reading data/images from SPI flash. This is useful for boards that have SPL size constraints and would need to use SPI flash framework just to read images/data from flash. There is approximately 1.5 to 2KB savings with this. Based on prior work of reducing spi flash id table by Simon Goldschmidt Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed

mtd: spi: Remove unused files

2019-02-07T10:03:21Z

spi_flash and spi_flash_ids are no longer needed after SPI NOR migration. Remove them. Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed

mtd: spi: Switch to new SPI NOR framework

2019-02-07T10:03:21Z

Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD layer. Fix up sf_dataflash to work in legacy way. And update sandbox to use new interfaces/definitions Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed

mtd: spi: sf_probe: Add "jedec, spi-nor" compatible string

2019-02-07T10:03:21Z

Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible SPI Flash device nodes. Therefore make U-Boot also to look for the same compatible string so that we can use Linux DTS files as is. Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Tested-by: Jagan Teki #zynq-microzed

mtd: spi: spi-nor-core: Add back U-Boot specific features

2019-02-07T10:03:21Z

For legacy reasons, we will have to keep around U-Boot specific SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework Signed-off-by: Vignesh R Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed

mtd: spi: spi-nor-core: Add SFDP support

2019-02-07T10:03:21Z

Sync Serial Flash Discoverable Parameters (SFDP) parsing support from Linux. This allows auto detection and configuration of Flash parameters. Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed

mtd: spi: spi-nor-core: Add 4 Byte addressing support

2019-02-07T10:03:21Z

Sync changes from Linux SPI NOR framework to add 4 byte addressing support. This is required in order to support flashes like MT35x that no longer support legacy Bank Address Register(BAR) way of accessing >16MB region. Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed

mtd: spi: spi-nor-core: Add SPI MEM support

2019-02-07T10:03:21Z

Many SPI controllers have special MMIO interfaces which provide accelerated read/write access but require knowledge of flash parameters to make use of it. Recent spi-mem layer provides a way to support such controllers. Therefore, add spi-mem support to spi-nor-core as a way to support SPI controllers with MMIO interface. SPI MEM layer takes care of translating spi_mem_ops to spi_xfer()s in case of legacy SPI controllers. Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed

mtd: spi: Port SPI NOR framework from Linux

2019-02-07T10:03:21Z

Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not support 4 byte addressing opcodes, SFDP table parsing and different types of quad mode enable sequences. Many newer flashes no longer support BANK registers used by sf layer to a access >16MB of flash address space. So, sync SPI NOR framework from Linux v4.19 that supports all the above features. Start with basic sync up that brings in basic framework subsequent commits will bring in more features. Signed-off-by: Vignesh R Tested-by: Simon Goldschmidt Tested-by: Stefan Roese Tested-by: Horatiu Vultur Reviewed-by: Jagan Teki Tested-by: Jagan Teki #zynq-microzed