u-boot.git/drivers/net/Kconfig, branch v2017.05

sunxi: Convert CONFIG_RGMII to Kconfig

2017-04-20T11:20:29Z

Convert CONFIG_RGMII to Kconfig. Thanks to that, it is possible to update defconfig files of SYS_EXTRA_OPTIONS accordingly and remove it when it is possible. Signed-off-by: Mylène Josserand Signed-off-by: Maxime Ripard

sunxi: Convert SUNXI_EMAC to Kconfig

2017-04-20T11:19:59Z

Convert the SUNXI_EMAC config to Kconfig. Remove it from SYS_EXTRA_OPTIONS from many sunxi defconfig and renamed it into SUN4I_EMAC to not confuse it with SUN8I_EMAC. Signed-off-by: Mylène Josserand Signed-off-by: Maxime Ripard

sunxi: Move SUNXI_GMAC to Kconfig

2017-04-20T11:19:56Z

Move the SUNXI_GMAC config option to Kconfig, remove it from SYS_EXTRA_OPTIONS and rename it into SUN7I_GMAC. Signed-off-by: Mylène Josserand Signed-off-by: Maxime Ripard

net: mvpp2: Enable compilation for Armada 7K/8K platforms

2017-03-29T05:42:20Z

Since Armada 7K/8K is also equipped with a newer version of the MVPP2 ethernet controller, lets enable compilation of this driver for these platforms. Signed-off-by: Stefan Roese Acked-by: Joe Hershberger

drivers/net/Kconfig: Correct use of apostrophe

2017-02-27T17:14:58Z

Signed-off-by: Tom Rini

drivers: net: Provide Kconfig menu for PHYLIB

2017-02-07T17:05:03Z

Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc Acked-by: Joe Hershberger

net: Kconfig: Add CONFIG_MACB option

2017-02-07T16:54:31Z

Add CONFIG_MACB option in KConfig to be used to select the Cadence MACB Ethernet driver. Signed-off-by: Wenyou Yang

net: gmac_rockchip: Add Rockchip GMAC driver

2017-01-12T03:23:50Z

Add a new driver for the GMAC ethernet interface present in Rockchip RK3288 SOCs. This driver subclasses the generic design-ware driver to add the glue needed specifically for Rockchip. Signed-off-by: Sjoerd Simons Signed-off-by: Simon Glass Signed-off-by: Romain Perier Acked-by: Joe Hershberger

arm: imx: add i.MX53 Beckhoff CX9020 Embedded PC

2016-12-16T11:57:12Z

Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn

net: add driver for Synopsys Ethernet QoS device

2016-11-07T17:28:15Z

This driver supports the Synopsys Designware Ethernet QoS (Quality of Service) a/k/a eqos IP block, which is a different design than the HW supported by the existing designware.c driver. The IP supports many options for bus type, clocking/reset structure, and feature list. This driver currently supports the specific configuration used in NVIDIA's Tegra186 chip, but should be extensible to other combinations quite easily, as explained in the source. Signed-off-by: Stephen Warren Reviewed-by: Simon Glass # V1 Acked-by: Joe Hershberger