u-boot.git/drivers/net/Kconfig, branch v2020.04

net: Add support for Broadcom GENETv5 Ethernet controller

2020-01-29T17:30:33Z

The Broadcom GENET Ethernet MACs are used in several MIPS based SoCs and in the Broadcom 2711/2838 SoC used on the Raspberry Pi 4. There is no publicly available documentation, so this driver is based on the Linux driver. Compared to that the queue management is drastically simplified, also we only support version 5 of the IP and RGMII connections between MAC and PHY, as used on the RPi4. Signed-off-by: Amit Singh Tomar Reviewed-by: Andre Przywara [Andre: heavy cleanup and a few fixes] Signed-off-by: Andre Przywara Tested-by: Corentin Labbe Signed-off-by: Matthias Brugger

drivers: net: add mcf fec dm Kconfig support

2020-01-10T15:25:13Z

Add ColdFire fec to Kconfig. Signed-off-by: Angelo Durgehello

net: mvpp2: MVPP2 now needs MVMDIO

2019-12-09T15:47:42Z

Changes to mvpp2.c require the MVMDIO module which in turn uses DM_MDIO. Signed-off-by: Nevo Hed Reviewed-by: Ramon Fried Acked-by: Joe Hershberger

net: Kconfig: FEC: Add dependency on i.MX8M

2019-11-05T09:27:18Z

Make FEC driver could be used by i.MX8M when CONFIG_FEC_MXC defined in defconfig. Signed-off-by: Peng Fan Reviewed-by: Frieder Schrempf Tested-by: Frieder Schrempf

net: mt7628-eth: make phy link up detection optional via DT

2019-10-25T15:20:44Z

The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port). Although in IOT mode only port0 is usable, the phy0 is still connected to the switch, not the ethernet gmac directly. This patch rewrites it and makes it optional. It can be turned on by adding mediatek,poll-link-phy = explicitly into the eth node. By default the driver is switch mode with all 5 phy ports working without link detection. Signed-off-by: Weijie Gao

drivers: net: add marvell MDIO driver

2019-09-04T16:37:19Z

This patch adds a separate driver for the MDIO interface of the Marvell Ethernet controllers based on driver model. There are two reasons to have a separate driver rather than including it inside the MAC driver itself: *) The MDIO interface is shared by all Ethernet ports, so a driver must guarantee non-concurrent accesses to this MDIO interface. The most logical way is to have a separate driver that handles this single MDIO interface, used by all Ethernet ports. *) The MDIO interface is the same between the existing mv643xx_eth driver and the new mvneta/mvpp2 driver. Even though it is for now only used by the mvneta/mvpp2 driver, it will in the future be used by the mv643xx_eth driver as well. This driver supports SMI IEEE for 802.3 Clause 22 and XSMI for IEEE 802.3 Clause 45. This patch also adds device tree binding for marvell MDIO driver. Signed-off-by: Ken Ma Signed-off-by: Alex Marginean Acked-by: Joe Hershberger

drivers/fsl-mc: Create Kconfig file to manage driver specific configs better

2019-09-04T16:37:19Z

Create drivers/net/fsl-mc/Kconfig and move fsl-mc specific configs from arch/arm/cpu/armv8/fsl-layerscape/Kconfig to this new Kconfig Signed-off-by: Florinel Iordache Acked-by: Joe Hershberger

drivers: net: driver for MDIO muxes controlled over I2C

2019-09-04T16:37:19Z

This driver is used for MDIO muxes driven over I2C. This is currently used on Freescale LS1028A QDS board, on which the physical MDIO MUX is controlled by an on-board FPGA which in turn is configured through I2C. Signed-off-by: Alex Marginean Acked-by: Joe Hershberger Reviewed-by: Bin Meng

Revert "drivers: net: driver for MDIO muxes controlled over I2C"

2019-09-04T16:37:19Z

This reverts commit d9a9174fa5687521035b2ec82cce86cdcf4f36e6.

doc: arch: sandbox: Replace all the instances of README.sandbox

2019-07-29T13:32:09Z

commit 49116e6d236d ("doc: arch: Convert README.sandbox to reST") Moves README.sandbox to doc/arch. Replace all the existing instances to point to the right documentation file. Signed-off-by: Keerthy