This patch adds a separate driver for the MDIO interface of the
Marvell Ethernet controllers based on driver model. There are two
reasons to have a separate driver rather than including it inside
the MAC driver itself:
  *) The MDIO interface is shared by all Ethernet ports, so a driver
     must guarantee non-concurrent accesses to this MDIO interface. The
     most logical way is to have a separate driver that handles this
     single MDIO interface, used by all Ethernet ports.
  *) The MDIO interface is the same between the existing mv643xx_eth
     driver and the new mvneta/mvpp2 driver. Even though it is for now
     only used by the mvneta/mvpp2 driver, it will in the future be
     used by the mv643xx_eth driver as well.

This driver supports SMI IEEE for 802.3 Clause 22 and XSMI for IEEE
802.3 Clause 45.

This patch also adds device tree binding for marvell MDIO driver.

Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This driver is used for MDIO muxes driven over I2C.  This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

This reverts commit d9a9174fa5687521035b2ec82cce86cdcf4f36e6.

This driver is used for MDIO muxes driven over I2C.  This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

Adds a driver for the MDIO interface currently integrated in LS1028A SoC.
This MDIO interface is shared by multiple ethernet interfaces and is
presented as a stand-alone PCI function on the SoC ECAM.
Ethernet has a functional dependency on MDIO, for simplicity there is a
single config option for both.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Adds a driver for NXP ENETC ethernet controller currently integrated in
LS1028A.  ENETC is a fairly straight-forward BD ring device and interfaces
are presented as PCI EPs on the SoC ECAM.

Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Adds a test using a makeshift MDIO MUX.  The test is based on the existing
MDIO test.  It uses the last emulated PHY register to verify MUX selection.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

A very simple test for DM_MDIO, mimicks a register write/read through the
sandbox bus to a dummy PHY.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200.  It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>