u-boot.git/drivers/net/Makefile, branch v2021.04

sh: Remove r7780mp board

2021-02-15T15:16:23Z

This board has not been converted to CONFIG_DM by the deadline of v2020.01 and is missing other conversions which depend on this as well. Remove it. Patch-cc: Nobuhiro Iwamatsu Patch-cc: Nobuhiro Iwamatsu Signed-off-by: Tom Rini

net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs

2021-01-27T15:47:44Z

Add Cortina Access Ethernet device driver for CAxxxx SoCs. This driver supports both legacy and DM_ETH network models. Signed-off-by: Aaron Tseng Signed-off-by: Alex Nemirovsky Signed-off-by: Abbie Chang CC: Joe Hershberger CC: Abbie Chang CC: Tom Rini

net: add ethernet driver for MediaTek MT7620 SoC

2021-01-24T20:39:27Z

This patch adds ethernet driver for MediaTek MT7620 SoC. The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in 7-port switch and two xMII interfaces (can be MII/RMII/RGMII). The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be configured to connect to either the intergrited FE PHY, or the xMII. Port 5 always connects to the xMII. Port 6 is the CPU port. This driver supports MT7530 giga switch connects to port 5. Reviewed-by: Stefan Roese Signed-off-by: Weijie Gao

net: Add IPQ40xx MDIO driver

2020-10-22T13:54:54Z

This adds the driver for the IPQ40xx built-in MDIO. This will be needed to support future PHY driver. Signed-off-by: Robert Marko Cc: Luka Perkov

net: Add NIC controller driver for OcteonTX2

2020-10-14T05:55:56Z

Adds support for Network Interface controllers found on OcteonTX2 SoC platforms. Signed-off-by: Suneel Garapati Signed-off-by: Stefan Roese Cc: Joe Hershberger

net: Add NIC controller driver for OcteonTX

2020-10-14T05:55:56Z

Adds support for Network Interface controllers found on OcteonTX SoC platforms. Signed-off-by: Suneel Garapati Signed-off-by: Stefan Roese Cc: Joe Hershberger

net, qe: add DM support for QE UEC ethernet

2020-09-17T04:09:53Z

add DM/DTS support for the UEC ethernet on QUICC Engine Block. Signed-off-by: Heiko Schocher Patch-cc: Mario Six Patch-cc: Qiang Zhao Patch-cc: Holger Brunck Patch-cc: Madalin Bucur Series-changes: 3 - revert: commit "3374264df97b" ("drivers: net: qe: deselect QE when DM_ETH is enabled") as now qe works with DM and DM_ETH support. - fix mailaddress from Holger Series-changes: 2 - add comments from Qiang Zhao: - add device node documentation - I did not drop the dm_qe_uec_phy.c and use drivers/net/fsl_mdio.c because using drivers/net/fsl_mdio.c leads in none existent udevice mdio@3320 instead boards with DM ETH support should use now this driver. - remove RFC tag Commit-notes: - I let the old none DM based implementation in code so boards should work with old implementation. This Code should be removed if all boards are converted to DM/DTS. - add the DM based qe uec driver under drivers/net/qe - Therefore copied the files uccf.c uccf.h uec.h from drivers/qe. So there are a lot of Codingstyle problems currently. I fix them in next version if this RFC patch is OK or it needs some changes. - The dm based driver code is now under drivers/net/qe/dm_qe_uec.c Used a lot of functions from drivers/qe/uec.c - seperated the PHY specific code into seperate file drivers/net/qe/dm_qe_uec_phy.c END

net: designware: s700: Add glue code for S700 mac

2020-07-07T21:11:58Z

This patchs adds glue logic to enable designware mac present on Action Semi based S700 SoC, Configures SoC specific bits. Undocumented bit that programs the PHY interface select register comes from vendor source. It has been tested on Cubieboard7-lite based on S700 SoC. Signed-off-by: Amit Singh Tomar

net: Add eth phy generic driver for shared MDIO

2020-05-10T11:24:48Z

For dual ethernet controllers, the HW design may connect ETH phys to one MDIO ports. So two different ethernet drivers have to share MDIO bus. Since two ethernet drivers are independent, we can't ensure their probe order. To resolve this problem, introduce an eth phy generic driver and uclass. After eth-uclass binds, we search the mdio node and binds the phy node with the eth-phy-generic driver. When one eth driver get its phy device, the parent of phy device will probe prior than phy device. So this ensure the eth driver ownes the MDIO bus will be probed before using its MDIO. Signed-off-by: Ye Li Signed-off-by: Peng Fan

drivers: net: add Layerscape mEMAC MDIO driver

2020-04-29T05:19:20Z

Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate Ethernet Media Access Controller) and the Fman 10G Ethernet MACs. Signed-off-by: Ioana Ciornei Reviewed-by: Priyanka Jain