u-boot.git/drivers/net/Makefile, branch v2021.10

net: xilinx: axi_mrmac: Add MRMAC driver

2021-07-26T07:18:45Z

Add support for xilinx multirate(MRMAC) ethernet driver. This driver uses multichannel DMA(MCDMA) for data transfers of MRMAC. Added support for 4 ports of MRMAC for speeds 10G and 25G. MCDMA supports upto 16 channels but in this driver we have setup only one channel which is enough. Tested 10G and 25G on all 4 ports. Signed-off-by: Ashok Reddy Soma Signed-off-by: Michal Simek

net: add support for KSZ9477/KSZ9897/KSZ9567 GbE switch

2021-07-10T16:12:42Z

The Microchip KSZ9477/KSZ9897/KSZ9567 7-Port Gigabit Ethernet Switches support SGMII/RGMII/MII/RMII with register access via SPI, I2C, or MDIO. This driver currently supports I2C register access but SPI or MDIO register access can be easily added at a later time. Tagging is not implemented and instead the active port is tracked to avoid needing a tag to store port information. This was tested with the imx8mm-venice-gw7901 board which has a KSZ9897S switch with an IMX8MM FEC MAC master connected via RGMII_ID. Signed-off-by: Tim Harvey Reviewed-by: Ramon Fried

net: synquacer: Add netsec driver

2021-06-18T08:29:17Z

Add SynQuacer's NETSEC GbE controller driver. Since this driver will load the firmware from SPI NOR flash, this depends on CONFIG_SYNQUACER_SPI=y. Signed-off-by: Jassi Brar Reviewed-by: Ramon Fried

net: Remove ne2000 driver

2021-05-25T16:40:16Z

With the last user of this driver removed, remove the driver. Reviewed-by: Daniel Schwierzeck Signed-off-by: Tom Rini

sandbox: Add a DSA sandbox driver and unit test

2021-04-15T08:52:17Z

The DSA sandbox driver is used for unit testing the DSA class code. It implements a simple 2 port switch plus 1 CPU port, and uses a very simple tag to identify the ports. The DSA sandbox device is connected via CPU port to a regular Ethernet sandbox device, called 'dsa-test-eth, managed by the existing eth sandbox driver. The 'dsa-test-eth' is not intended for testing the eth class code however, but it is used to emulate traffic through the 'lan0' and 'lan1' front pannel switch ports. To achieve this the dsa sandbox driver registers a tx handler for the 'dsa-test-eth' device. The switch ports, labeled as 'lan0' and 'lan1', are also registered as eth devices by the dsa class code this time. So pinging through these switch ports is as easy as: => setenv ethact lan0 => ping 1.2.3.5 Unit tests for the dsa class code were also added. The 'dsa_probe' test exercises most API functions from dsa.h. The 'dsa' unit test simply exercises ARP/ICMP traffic through the two switch ports, including tag injection and extraction, with the help of the dsa sandbox driver. I took care to minimize the impact on the existing eth unit tests, though some adjustments needed to be made with the addition of extra eth interfaces used by the dsa unit tests. The additional eth interfaces also require MAC addresses, these have been added to the sandbox default environment. Signed-off-by: Alex Marginean Signed-off-by: Claudiu Manoil Reviewed-by: Simon Glass Signed-off-by: Vladimir Oltean Message-Id: <20210216224804.3355044-5-olteanv@gmail.com> Signed-off-by: Bin Meng Reviewed-by: Priyanka Jain

net: designware: add Amlogic Meson8b & later glue driver

2021-04-06T09:10:29Z

This adds a proper glue driver for the Designware DWMAC ethernet MAC IP found in the Amlogic Meson8, GXBB, GXL, GXM, G12A, G12B & SM1 SoCs. This is aimed to replace the static ethernet link setup found on the board init code for the Amlogic SoC based boards. Tested on a libretech-cc (S905x Internal RMII 10/100 PHY) and Khadas VIM3 (A113d with external 10/100/1000 RGMII PHY) to cover the most extreme setups. Signed-off-by: Neil Armstrong

net: add Amlogic Meson G12A MDIO MUX driver

2021-04-06T09:10:29Z

The Amlogic G12A & compatible SoCs embeds a mux to either communicate with the external PHY or the internal 10/100 PHY. This adds support for this mux as a MDIO MUX device. Signed-off-by: Neil Armstrong Reviewed-by: Ramon Fried

net: add MMIO Register MDIO MUX driver

2021-04-06T09:10:29Z

Add support for MMIO register MDIO muxes based on the Linux mdio-mux-mmioreg driver. Signed-off-by: Neil Armstrong Reviewed-by: Ramon Fried

sh: Remove r7780mp board

2021-02-15T15:16:23Z

This board has not been converted to CONFIG_DM by the deadline of v2020.01 and is missing other conversions which depend on this as well. Remove it. Patch-cc: Nobuhiro Iwamatsu Patch-cc: Nobuhiro Iwamatsu Signed-off-by: Tom Rini

net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs

2021-01-27T15:47:44Z

Add Cortina Access Ethernet device driver for CAxxxx SoCs. This driver supports both legacy and DM_ETH network models. Signed-off-by: Aaron Tseng Signed-off-by: Alex Nemirovsky Signed-off-by: Abbie Chang CC: Joe Hershberger CC: Abbie Chang CC: Tom Rini