u-boot.git/drivers/net/designware.c, branch v2016.03

net: designware: Use dm_pci_mem_to_phys() in the probe routine

2016-02-05T04:47:23+00:00

Convert to use native DM PCI API dm_pci_mem_to_phys().

Signed-off-by: Bin Meng 
Reviewed-by: Simon Glass

Merge branch 'master' of git://git.denx.de/u-boot-net

2016-01-28T23:42:10+00:00

net/designware: add support of max-speed device tree property

2016-01-28T18:32:44+00:00

This property allows to specify fastest connection mode supported by
the MAC (as opposed to features of the phy).

There are situations when phy may handle faster modes than the
MAC (or even it's particular implementation or even due to CPU being too
slow).

This property is a standard one in Linux kernel these days and some
boards do already use it in their device tree descriptions.

Signed-off-by: Alexey Brodkin 
Cc: Bin Meng 
Cc: Joe Hershberger 
Cc: Sonic Zhang 
cc: Simon Glass 
Acked-by: Joe Hershberger

net/designware: do explicit port selection for 1Gb mode

2016-01-28T18:32:43+00:00

Current implementation only sets "port select" bit for non-1Gb mode.
That works fine if GMAC has just exited reset state but we may as well
change connection mode in runtime. Then we'll need to reprogram GMAC for
that new mode of operation and if previous mode was 10 or 100 Mb and new
one is 1 Gb we'll need to reset port mode bit.

Signed-off-by: Alexey Brodkin 
Cc: Bin Meng 
Cc: Joe Hershberger 
Cc: Sonic Zhang 
cc: Simon Glass 
Acked-by: Joe Hershberger

Fix GCC format-security errors and convert sprintfs.

2016-01-15T03:11:34+00:00

With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.

Simple uses of sprintf are also converted to use strcpy.

Signed-off-by: Ben Whitten 
Acked-by: Wolfgang Denk 
Reviewed-by: Tom Rini

dm: pci: Add a dm_ prefix to pci_get_bdf()

2016-01-12T17:19:09+00:00

Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.

For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_get_bdf() accordingly.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

net: designware: Zap trailing backslash

2015-12-22T03:42:27+00:00

Trailing backslashes are necessary only in macros, not in the actual
code, so remove them.

Signed-off-by: Marek Vasut 
Cc: Dinh Nguyen 
Cc: Joe Hershberger

net: eth_designware: select PHYLIB in Kconfig

2015-12-22T03:42:27+00:00

Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.

This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.

Signed-off-by: Thomas Chou 
Reported-by: Pavel Machek 
Acked-by: Chin Liang See 
Acked-by: Pavel Machek 
Tested-by: Pavel Machek 
Reviewed-by: Bin Meng

net: designware: Add driver remove support

2015-10-29T19:05:50+00:00

In designware_eth_probe(), some additional resources are allocated
(eg: mdio, phy). We should free these in the driver remove phase.
Add designware_eth_remove() to clean it up.

Signed-off-by: Bin Meng 
Acked-by: Simon Glass

net: designware: Add support to PCI designware devices

2015-09-17T01:53:52+00:00

The Designware ethernet controller is also seen on PCI bus, e.g.
on Intel Quark SoC. Add this support in the DM version driver.

Signed-off-by: Bin Meng 
Acked-by: Simon Glass