u-boot.git/drivers/net/fsl_enetc.h, branch master

net: fsl_enetc: Add iMX95 enetc4 10Gbps port support

2026-04-21T23:49:39+00:00

1. Add optional serdes-supply regulator property support.
2. Enable 10Gbps feature for the controller, configure netc blkctrl
   CFG_LINK_PCS_PROT_2 to 10G SXGMII.
3. Add internal xpcs phy initialization to 10G XGMII Mode without
   auto-negotiation interface.

Signed-off-by: Ye Li 
Signed-off-by: Alice Guo

net: fsl_enetc: Update enetc driver to support i.MX95

2025-01-20T11:40:39+00:00

i.MX95 uses enetc version 4.1 controller. Update the enetc for i.MX95.
Add ARM-specific cache handling and i.MX95 specific register layout
handling.

Signed-off-by: Alice Guo 
Signed-off-by: Marek Vasut  # Clean up
Signed-off-by: Ye Li 
Reviewed-by: Tim Harvey

net: fsl_enetc: add i.MX95 EMDIO support

2025-01-20T11:40:39+00:00

The verdor ID and device ID of i.MX95 EMDIO are different from LS1028A
EMDIO, so add new vendor ID and device ID to pci_device_id table to
support i.MX95 EMDIO.

Signed-off-by: Alice Guo 
Signed-off-by: Marek Vasut  # Clean up
Signed-off-by: Ye Li

net: fsl_enetc: Introduce driver data

2025-01-20T11:40:39+00:00

Introduce driver data for each PCI device. The driver data carry
offsets of registers which differ between different SoCs.

Signed-off-by: Marek Vasut

net: fsl_enetc: Split register accessors

2025-01-20T11:40:39+00:00

Split register accessors to the port base/station interface/port/mac
registers as those are at different offsets on different SoCs. This
is a preparatory patch which will allow addition of adjusted offsets
for new SoCs easily.

Signed-off-by: Marek Vasut

net: fsl_enetc: Inline register accessors

2025-01-20T11:40:39+00:00

Move register accessors from header files and turn them into proper
inline functions, so typechecking can be done on them. Drop no longer
enetc_port_regs() and unused enetc_read() and enetc_bdr_read().

Signed-off-by: Marek Vasut

blk: Rename if_type to uclass_id

2022-09-25T14:30:05+00:00

Use the word 'uclass' instead of 'if_type' to complete the conversion.

Signed-off-by: Simon Glass

net: enetc: force the RGMII MAC speed/duplex instead of using in-band signaling

2021-07-06T02:22:41+00:00

The RGMII spec supports optional in-band status reporting for the speed
and duplex negotiated on the copper side, and the ENETC driver enables
this feature by default.

However, this does not work when the PHY does not implement the in-band
reporting, or when there is a MAC-to-MAC connection described using a
fixed-link. In that case, it would be better to disable the feature in
the ENETC MAC and always force the speed and duplex to the values that
were negotiated and retrieved over MDIO once the autoneg is finished.
Since this works always, we just do it unconditionally and drop the
in-band code.

Note that because we need to wait for the autoneg to complete, we need
to move enetc_setup_mac_iface() after phy_startup() returns, and then
pass the phydev pointer all the way to enetc_init_rgmii().

The same considerations have led to a similar Linux driver patch as well:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c76a97218dcbb2cb7cec1404ace43ef96c87d874

Signed-off-by: Vladimir Oltean 
Reviewed-by: Ramon Fried

drivers: net: Add Felix DSA switch driver

2021-02-16T17:38:36+00:00

This driver is used for the Ethernet switch integrated into LS1028A NXP.
Felix on LS1028A has 4 front panel ports and two internal ports, I/O
to/from the switch is done through an ENETC Ethernet interface.
The 4 front panel ports are available as Ethernet interfaces and can be
used with the typical network commands like tftp.

Signed-off-by: Alex Marginean 
Signed-off-by: Claudiu Manoil 
Signed-off-by: Vladimir Oltean

common: Drop linux/bitops.h from common header

2020-05-19T01:19:23+00:00

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass