AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This patch adds support for searching through available PHY-addresses in
the macb-driver. This is needed for the ATEVK1100 evaluation board,
where the PHY-address will be initialized to either 1 or 7.

This patch adds a config option, CONFIG_MACB_SEARCH_PHY, which when
enabled tells the driver to search for the PHY address.

Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

Replace COBJS-y with appropriate driver config names.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>

This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Support for booting from internal DataFlash, external DataFlash card
or NAND flash is available.

Signed-off-by: Stelian Pop <stelian@popies.net>

Signed-off-by: Stelian Pop <stelian <at> popies.net>
Acked-by: Haavard Skinnemoen <hskinnemoen <at> atmel.com>

Change return values of init() functions in all Ethernet drivers to conform
to the following:

    >=0: Success
    <0:  Failure

All drivers going forward should return 0 on success.  Current drivers that
return 1 on success were left as-is to minimize changes.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-By: Timur Tabi <timur@freescale.com>