u-boot.git/drivers/net/mvgbe.c, branch main

treewide: move bi_dram[] from bd to gd

2026-06-25T00:13:24Z

Currently, the bi_dram[] information is stored in the board info structure (bd). Because bd is only valid after reserve_board(), dram_init_banksize() must be called late in the initialization process. This limitation is problematic, as it forces us to rely on a variety of bespoke functions to determine board RAM, bank memory sizes, and other early setup requirements. By moving bi_dram[] into the global data (gd), we can run it earlier. This is particularly convenient since boards define their own dram_init_banksize() routines, which do not always rely on parsing Device Tree (DT) memory nodes. Additionally, U-Boot defaults to relocating to the top of the first memory bank. While boards currently use custom functions to override this behavior, having the DRAM bank information available earlier in gd makes relocating to a different bank trivial and standardizes the process. Reviewed-by: Anshul Dalal Tested-by: Michal Simek # Versal Gen 2 Vek385 Tested-by: Anshul Dalal Reviewed-by: Simon Glass Signed-off-by: Ilias Apalodimas Tested-by: Christophe Leroy (CS GROUP)

arm: Remove remainder of ARCH_ORION5X

2026-01-21T18:05:15Z

With commit 5663b137e682 ("arm: Remove edminiv2 board") the last ARCH_ORION5X platform was removed. Remove the rest of the architecture code which is now unused. Reviewed-by: Tony Dinh Signed-off-by: Tom Rini

Restore patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"

2024-05-20T19:35:03Z

As part of bringing the master branch back in to next, we need to allow for all of these changes to exist here. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

2024-05-19T14:16:36Z

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"' I failed to notice that b4 noticed it was based on next and so took that as the base commit and merged that part of next to master. This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

net: Remove and add needed includes

2024-05-07T14:00:55Z

Remove from this driver directory and when needed add missing include files directly. Signed-off-by: Tom Rini

global: Remove unused CONFIG symbols

2022-12-22T15:31:48Z

This removes the following unreferenced CONFIG symbols: CONFIG_FDTADDR CONFIG_FDTFILE CONFIG_FLASH_SECTOR_SIZE CONFIG_FSL_CPLD CONFIG_HDMI_ENCODER_I2C_ADDR CONFIG_I2C_MVTWSI CONFIG_I2C_RTC_ADDR CONFIG_IRAM_END CONFIG_IRAM_SIZE CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE CONFIG_L1_INIT_RAM CONFIG_MACB_SEARCH_PHY CONFIG_MIU_2BIT_21_7_INTERLEAVED CONFIG_MTD_NAND_VERIFY_WRITE CONFIG_MVGBE_PORTS CONFIG_NETDEV CONFIG_NUM_DSP_CPUS CONFIG_PHY_BASE_ADR CONFIG_PHY_INTERFACE_MODE CONFIG_PSRAM_SCFG CONFIG_RAMBOOT_SPIFLASH CONFIG_RAMBOOT_TEXT_BASE CONFIG_RD_LVL CONFIG_ROCKCHIP_SDHCI_MAX_FREQ CONFIG_SETUP_INITRD_TAG CONFIG_SH_QSPI_BASE CONFIG_SMDK5420 CONFIG_SOCRATES CONFIG_SPI_ADDR CONFIG_SPI_FLASH_QUAD CONFIG_SPI_FLASH_SIZE CONFIG_SPI_HALF_DUPLEX CONFIG_SPI_N25Q256A_RESET CONFIG_TEGRA_SLINK_CTRLS CONFIG_TPM_TIS_BASE_ADDRESS CONFIG_UBOOT_SECTOR_COUNT CONFIG_UBOOT_SECTOR_START CONFIG_VAR_SIZE_SPL CONFIG_VERY_BIG_RAM And also: BL1_SIZE PHY_NO RESERVE_BLOCK_SIZE Signed-off-by: Tom Rini

net: mvgbe: Remove non-DM_ETH code

2022-12-07T21:04:17Z

As DM_ETH is required for all network drivers, it's now safe to remove the non-DM_ETH support code. Signed-off-by: Tom Rini

net: marvell: mvgbe: Set PHY page 0 before phy_connect

2022-05-02T05:47:26Z

For most Kirkwood boards, the PHY page is already set to page 0 (in register 22) before phy_connect is invoked. But some board like the Zyxel NSA310S (which uses the network chip MV88E1318S), the PHY page is not set to page 0. There seems to be some bad data remained in register 22 when the uclass MVGBE about to invoke phy_connect(). This patch enables the uclass MVGBE to always set the PHY page to 0 before phy_connect. For reference, please see this discussion: [RFC PATCH v2] arm: kirkwood: nsa310s: Use Marvell uclass mvgbe and PHY driver for DM Ethernet. https://lists.denx.de/pipermail/u-boot/2022-April/480946.html This patch has been tested with the following Kirkwood boards: NSA310S (88F6702, network chip MV88E1318S) Sheevaplug (88F6281, network chip MV88E1318) Pogo V4 (88F6192, network chip 88E1116R) GF Home(88F6281, network chip 88E1116R) Dreamplug (88F6281, network chip MV88E1318) Dell Kace M300 (88F6282, network chip MV88E1318) - out of tree u-boot Signed-off-by: Tony Dinh

treewide: Rename PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA

2022-04-10T05:44:13Z

Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make it compatible with Linux' naming. Signed-off-by: Marek Behún Reviewed-by: Stefan Roese Reviewed-by: Ramon Fried Reviewed-by: Vladimir Oltean

net: introduce helpers to get PHY interface mode from a device/ofnode

2022-04-10T05:44:12Z

Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the "phy-mode" / "phy-connection-type" property. Add corresponding UT test. Use them treewide. This allows us to inline the phy_get_interface_by_name() into ofnode_read_phy_mode(), since the former is not used anymore. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Tested-by: Patrice Chotard