u-boot.git/drivers/net/phy/Kconfig, branch v2017.07

Merge git://www.denx.de/git/u-boot-imx

2017-06-27T13:32:37Z

Signed-off-by: Tom Rini Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h

net: Kconfig:make PHY_GIGE and individual Micrel PHYs selectable

2017-06-02T19:44:18Z

This change migrate the following configuration options for Kconfig: * PHY_GIGE, indicates that a controller (with an appropriate PHY) is Gigabit capable and enables extra support in the miiutil for parsing the status of Gigabit PHYs * adds configuration options for Micrel KSZ9021 and KSZ9031 GbE PHYs, which previously had to enabled through a board-specific config file Signed-off-by: Philipp Tomsich Acked-by: Maxime Ripard Acked-by: Joe Hershberger

drivers: net: Kconfig: Add PHY_MICREL_KSZ9021 entry

2017-05-31T08:22:14Z

Add kconfig entry for Micrel KSZ9021 PHY support. Cc: Joe Hershberger Signed-off-by: Jagan Teki

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

2017-04-13T15:19:00Z

Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h Signed-off-by: Tom Rini

drivers/net/phy: add fixed-phy / fixed-link support

2017-03-26T14:58:26Z

This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer Signed-off-by: Hannes Schmelzer Acked-by: Joe Hershberger Reviewed-by: Christian Gmeiner

drivers: net: phy: add MV88E6xx options to Kconfig

2017-03-20T18:09:49Z

Signed-off-by: Tim Harvey Reviewed-by: Stefano Babic Acked-by: Joe Hershberger

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

2017-02-08T22:32:58Z

Signed-off-by: John Haechten Acked-by: Joe Hershberger

drivers: net: Provide Kconfig menu for PHYLIB

2017-02-07T17:05:03Z

Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc Acked-by: Joe Hershberger