u-boot.git/drivers/net/phy/Kconfig, branch v2018.09

net: phy: Don't limit phy addresses by default

2018-04-13T20:56:47Z

Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger Tested-by: Bin Meng Acked-by: Neil Armstrong Reviewed-by: Philipp Tomsich

net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek phys

2018-03-22T20:05:27Z

Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans Acked-by: Joe Hershberger

Move CONFIG_PHY_ADDR to Kconfig

2018-03-13T17:06:33Z

CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev Acked-by: Maxime Ripard [jagan: rebased on master] Signed-off-by: Jagan Teki Reviewed-by: Jagan Teki

Kconfig: net: phylib: Phylib should depends on NET

2018-02-08T17:48:10Z

There is no value to enable phylib without networking support. Signed-off-by: Michal Simek Acked-by: Joe Hershberger

net: phy: Add Broadcom BCM53xx switch driver

2018-01-15T18:05:21Z

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese Signed-off-by: Florian Fainelli

net: phy: Add Amlogic Meson GXL Internal PHY support

2017-11-17T12:44:13Z

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong

net: phy: Hide Micrel KSZ9021 and KSZ9031 Kconfig options

2017-08-07T20:18:30Z

The correct option is PHY_MICREL_KSZ90X1, but some configs still select the 9021 and 9031 options, which are deprecated. Signed-off-by: Alexandru Gagniuc Reviewed-by: Philipp Tomsich Acked-by: Joe Hershberger

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

2017-08-07T20:18:30Z

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc Reviewed-by: Philipp Tomsich Acked-by: Joe Hershberger

net: phy: Remove duplicate Kconfig selection for Micrel KSZ9021

2017-08-07T20:18:29Z

Signed-off-by: Alexandru Gagniuc Reviewed-by: Philipp Tomsich Acked-by: Joe Hershberger

Merge git://www.denx.de/git/u-boot-imx

2017-06-27T13:32:37Z

Signed-off-by: Tom Rini Conflicts: include/configs/imx6qdl_icore_rqs.h include/configs/imx6ul_geam.h include/configs/imx6ul_isiot.h