u-boot.git/drivers/net/phy/Kconfig, branch v2022.01

Kconfig: Remove all default n/no options

2021-08-31T21:47:49Z

default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

2021-08-18T10:25:15Z

Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh Reviewed-by: Priyanka Jain

phy: add nxp tja1103 phy driver

2021-07-06T02:22:41Z

Add nxp tja1103 phy driver. Signed-off-by: Radu Pirea (NXP OSS) Reviewed-by: Ramon Fried

net: phy: xilinx: Drop #ifdef CONFIG_DM_ETH around phy_connect_gmii2rgmii()

2021-04-15T08:52:17Z

At present phy_connect_gmii2rgmii() is implemented using a DM API dev_of_offset() hence it cannot support a non-DM configuration. Remove the non-DM version prototype of phy_connect_gmii2rgmii() and make the driver depend on CONFIG_DM_ETH. Signed-off-by: Bin Meng Acked-by: Michal Simek Reviewed-by: Ramon Fried Reviewed-by: Vladimir Oltean Reviewed-by: Priyanka Jain

net: phy: ca_phy: Add driver for CAxxxx SoCs

2021-01-27T15:47:47Z

Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang Signed-off-by: Alex Nemirovsky CC: Joe Hershberger CC: Tom Rini CC: Aaron Tseng Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

2020-12-10T08:26:39Z

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal Reviewed-by: Priyanka Jain

net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust rx/tx timings

2020-07-07T20:09:22Z

RTL8201F PHY module found on Actions Semi Cubieboard7 seems to have specific Rx/Tx interface timings requirement for proper PHY operations. These timing values are not documented anywhere and picked from vendor code. This commits lets proper packets to be transmitted over the network. Signed-off-by: Amit Singh Tomar

net: phy: Add DP8382x phy registration to TI PHY init

2020-06-12T17:17:23Z

Add the DP8382X generic PHY registration to the TI PHY init file. Acked-by: Michal Simek Signed-off-by: Dan Murphy

net: phy: Add support for TI PHY init

2020-06-12T17:17:23Z

ti_phy_init function was allocated to the DP83867 PHY. This function name is to generic for a specific PHY. The function can be moved to a TI specific file that can register all TI PHYs that are defined in the defconfig. The ti_phy_init file will contain all TI PHYs initialization so that only phy_ti_init can be called from the framework. In addition to the above the config flag for the DP83867 needs to be changed in the Kconfig and dependent defconfig files. The config flag that was used for the DP83867 was also generic in nature so a more specific config flag for the DP83867 was created. Acked-by: Michal Simek Signed-off-by: Dan Murphy

phy: Add support for the NC-SI protocol

2020-03-09T23:11:23Z

This introduces support for the NC-SI protocol, modelled as a phy driver for other ethernet drivers to consume. NC-SI (Network Controller Sideband Interface) is a protocol to manage a sideband connection to a proper network interface, for example a BMC (Baseboard Management Controller) sharing the NIC of the host system. Probing and configuration occurs by communicating with the "remote" NIC via NC-SI control frames (Ethernet header 0x88f8). This implementation is roughly based on the upstream Linux implementation[0], with a reduced feature set and an emphasis on getting a link up as fast as possible rather than probing the full possible topology of the bus. The current phy model relies on the network being "up", sending NC-SI command frames via net_send_packet() and receiving them from the net_loop() loop (added in a following patch). The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent field definitions. [0]: https://github.com/torvalds/linux/tree/master/net/ncsi [1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h Signed-off-by: Samuel Mendoza-Jonas Reviewed-by: Joel Stanley Acked-by: Joe Hershberger