u-boot.git/drivers/net/phy/Kconfig, branch v2022.07

Merge branch 'next' of https://source.denx.de/u-boot/custodians/u-boot-net

2022-04-15T12:10:32Z

- DM9000 DM support - tftp server bug fix - mdio ofnode support functions - Various phy fixes and improvements. [trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c drivers/net/phy/phy.c include/phy.h]

net: phy: nxp-tja11xx: Add NXP TJA11xx PHY driver

2022-04-12T17:10:44Z

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Michael Trimarchi Signed-off-by: Ariel D'Alessandro Reviewed-by: Ramon Fried

phy: adin: add driver for Analog Devices ADIN1300 PHY

2022-04-10T05:44:13Z

The current implementation configures RGMII using device tree phy-mode property and then calls genphy_config adin_config_rgmii_mode is derived from: https://github.com/varigit/linux-imx/blob/lf-5.10.y_var04/drivers/net/phy/adin.c#L218-L262 Signed-off-by: Nate Drude Reviewed-by: Ramon Fried

Convert CONFIG_BITBANGMII_MULTI to Kconfig

2022-04-01T14:28:46Z

This converts the following to Kconfig: CONFIG_BITBANGMII_MULTI Signed-off-by: Tom Rini

Convert CONFIG_PHY_RESET_DELAY to Kconfig

2022-03-25T12:01:15Z

This converts the following to Kconfig: CONFIG_PHY_RESET_DELAY Cc: Ramon Fried Signed-off-by: Tom Rini

net: phy: Add support for ethernet-phy-id with gpio reset

2022-03-09T11:43:16Z

Ethernet phy like dp83867 is using strapping resistors to setup PHY address. On Xilinx boards strapping is setup on wires which are connected to SOC where internal pull ups/downs influnce phy address. That's why there is a need to setup pins properly (via pinctrl driver for example) and then perform phy reset. I can be workarounded by reset gpio done for mdio bus but this is not working properly when multiply phys sitting on the same bus. That's why it needs to be done via ethernet-phy-id driver where dt binding has gpio reset per phy. DT binding is available here: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml The driver is are reading the vendor and device id from valid phy node using ofnode_read_eth_phy_id() and creating a phy device. Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio support. Signed-off-by: Michal Simek Signed-off-by: T Karthik Reddy Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com

net: phy: add TI DP83869HM ethernet driver

2022-01-15T16:50:16Z

This driver is based on an older downstream TI kernel, with changes and cleanups to work with mainline device-tree bindings. Signed-off-by: Dominic Rath Signed-off-by: Christian Gmeiner Reviewed-by: Ramon Fried

net: phy: realtek: Add tx/rx delay config for 8211e

2021-11-23T07:57:56Z

Some boards need to change the tx/rx delay config in order for gigabit Ethernet to work. In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"), Realtek documented the bits for overriding the delays from the hardware straps. Copy the logic from linux, so the delay config is set from the PHY's interface type (the phy-mode property in the device tree). This removes the need for a one-off workaround for the Pine A64+ board. Signed-off-by: Samuel Holland Reviewed-by: Ramon Fried

Kconfig: Remove all default n/no options

2021-08-31T21:47:49Z

default n/no doesn't need to be specified. It is default option anyway. Signed-off-by: Michal Simek [trini: Rework FSP_USE_UPD portion] Signed-off-by: Tom Rini

configs: Migrate CORTINA_FW_ADDR and CORTINA_FW_LENGTH to Kconfig

2021-08-18T10:25:15Z

Use moveconfig.py script to convert below defines to Kconfig and move these entries to defconfigs. CONFIG_CORTINA_FW_ADDR CONFIG_CORTINA_FW_LENGTH Signed-off-by: Kuldeep Singh Reviewed-by: Priyanka Jain