u-boot.git/drivers/net/phy/Makefile, branch v2017.09

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

2017-08-07T20:18:30+00:00

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc 
Reviewed-by: Philipp Tomsich 
Acked-by: Joe Hershberger

drivers/net/phy: add fixed-phy / fixed-link support

2017-03-26T14:58:26+00:00

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer 

Signed-off-by: Hannes Schmelzer 
Acked-by: Joe Hershberger 
Reviewed-by: Christian Gmeiner

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

2017-02-08T22:32:58+00:00

Signed-off-by: John Haechten 
Acked-by: Joe Hershberger

phy: Add phy driver support for xilinx PCS/PMA core

2016-04-04T18:10:44+00:00

Add phy driver support for xilinx PCS/PMA core

Signed-off-by: Siva Durga Prasad Paladugu 
Signed-off-by: Kedareswara rao Appana 
Signed-off-by: Michal Simek

net: phy: Add support for Texas Instruments DP83867

2015-11-19T12:09:21+00:00

Code is taken from Linux kernel driver (v4.2).

Signed-off-by: Edgar E. Iglesias 
Signed-off-by: Michal Simek 
Reviewed-by: Tom Rini 
Acked-by: Joe Hershberger

phylib: add support for aquantia PHYs

2015-01-16T17:32:11+00:00

This patch supports AQ1202, AQ2104, AQR105 PHY.

Signed-off-by: Shaohui Xie 
Acked-by: Joe Hershberger 
Reviewed-by: York Sun

net/phy: Add support for CS4315/CS4340 PHY

2014-12-05T16:06:11+00:00

Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
  to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
  we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.

Signed-off-by: Shengzhou Liu 
Reviewed-by: York Sun

drivers: net: remove dead drivers

2014-08-21T16:01:11+00:00

The following configs are not defined at all:

 - CONFIG_INCA_IP_SWITCH
 - CONFIG_PBL2800_ETHER
 - CONFIG_PHY_ICPLUS

Signed-off-by: Masahiro Yamada

drivers: net: convert makefiles to Kbuild style

2013-10-31T17:22:13+00:00

Signed-off-by: Masahiro Yamada

Add GPL-2.0+ SPDX-License-Identifier to source files

2013-07-24T13:44:38+00:00

Signed-off-by: Wolfgang Denk 
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini