u-boot.git/drivers/net/phy/Makefile, branch v2018.03 Unnamed repository; edit this file 'description' to name the repository. net: phy: Add Broadcom BCM53xx switch driver 2018-01-15T18:05:21+00:00 Florian Fainelli f.fainelli@gmail.com 2017-12-09T22:59:54+00:00 137963d71a2b2e0a1ac1fd755e0bec1409c2cdbd Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar to the Marvell MV88E617x. This takes care of configuring the minimum amount out of the switch hardware such that each user visible port (configurable) and the CPU port can forward packets between each other while preserving isolation with other ports. This is useful for e.g: the Lamobo R1 board featuring a Broadcom BCM53125 switch. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> 
Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
net: phy: Add Amlogic Meson GXL Internal PHY support 2017-11-17T12:44:13+00:00 Neil Armstrong narmstrong@baylibre.com 2017-10-18T08:02:10+00:00 8995a96d1d6760c930e37fc92fb718624f5d8fbf The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY. The PHY acts as a generic PHY but needs a slight configuration right before it's configuration. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> 
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers 2017-08-07T20:18:30+00:00 Alexandru Gagniuc alex.g@adaptrum.com 2017-07-07T18:36:57+00:00 d397f7c45b0b87a7e1083c57a320c559e7848268 The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they share the same ID. Drivers for bothe PHYs cannot safely coexist, so the solution was to use #ifdefs to select between the two drivers. As a result KSZ9031, which has a unique ID, is now caught in the crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031 will not function properly, as some essential configuration code is ifdef'd-out. To prevent such situations, move the KSZ9000 drivers to a separate file, and place them under a separate Kconfig option. While it is possible to enable both KSZ8000 and KSZ9000 drivers at the same time, the assumption is that it is highly unlikely for a system to contain both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers will be enabled at any given time. Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> 
The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
drivers/net/phy: add fixed-phy / fixed-link support 2017-03-26T14:58:26+00:00 Hannes Schmelzer hannes.schmelzer@br-automation.com 2017-03-23T14:11:43+00:00 db40c1aa1c100d8a9e33206575efd8b3678f31db This patch adds support for having a "fixed-link" to some other MAC (like some embedded switch-device). For this purpose we introduce a new phy-driver, called "Fixed PHY". Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is described with a subnode below ethernet interface. Most ethernet drivers (unfortunately not all are following same scheme for searching/attaching phys) are calling "phy_connect(...)" for getting a phy-device. At this point we link in, we search here for a subnode called "fixed- link", once found we start phy_device_create(...) with the special phy- id PHY_FIXED_ID (0xa5a55a5a). During init the "Fixed PHY" driver has registered with this id and now gets probed, during probe we get all the details about fixed-link out of dts, later on the phy reports this values. Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com> 
This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541 2017-02-08T22:32:58+00:00 John Haechten john.haechten@microsemi.com 2016-12-09T22:15:17+00:00 a5fd13ad1913d9c66c47666dbedac7703a48e502 Signed-off-by: John Haechten <john.haechten@microsemi.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> 
Signed-off-by: John Haechten <john.haechten@microsemi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
phy: Add phy driver support for xilinx PCS/PMA core 2016-04-04T18:10:44+00:00 Siva Durga Prasad Paladugu siva.durga.paladugu@xilinx.com 2016-02-05T07:52:10+00:00 ed6fad3e25e945e7042a53e129adde6a27476c90 Add phy driver support for xilinx PCS/PMA core Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> 
Add phy driver support for xilinx PCS/PMA core

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
net: phy: Add support for Texas Instruments DP83867 2015-11-19T12:09:21+00:00 Edgar E. Iglesias edgar.iglesias@xilinx.com 2015-09-26T06:46:08+00:00 721aed79126ba954028137eabe71678523a8b157 Code is taken from Linux kernel driver (v4.2). Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> 
Code is taken from Linux kernel driver (v4.2).

Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
phylib: add support for aquantia PHYs 2015-01-16T17:32:11+00:00 Shaohui Xie Shaohui.Xie@freescale.com 2014-12-30T10:32:04+00:00 f7c38cf827a0cf9d5ab4ca60131dffa10a2e4309 This patch supports AQ1202, AQ2104, AQR105 PHY. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <yorksun@freescale.com> 
This patch supports AQ1202, AQ2104, AQR105 PHY.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
net/phy: Add support for CS4315/CS4340 PHY 2014-12-05T16:06:11+00:00 Shengzhou Liu Shengzhou.Liu@freescale.com 2014-11-10T10:32:29+00:00 9b18e5199ec42f9dc62c0da7f4fe7554e199980d Add support for Cortina CS4315/CS4340 10G PHY. - This driver loads CS43xx firmware from NOR/NAND/SPI/SD device to initialize Cortina PHY. - Cortina PHY has non-standard offset of PHY ID registers, thus we define own get_phy_id() to override default get_phy_id(). - To define macro CONFIG_PHY_CORTINA will enable this driver. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com> 
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
  to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
  we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
drivers: net: remove dead drivers 2014-08-21T16:01:11+00:00 Masahiro Yamada yamada.m@jp.panasonic.com 2014-08-03T23:11:37+00:00 368b4d2b49bbbf379d9334747fbbd2aaaafe4356 The following configs are not defined at all: - CONFIG_INCA_IP_SWITCH - CONFIG_PBL2800_ETHER - CONFIG_PHY_ICPLUS Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> 
The following configs are not defined at all:

 - CONFIG_INCA_IP_SWITCH
 - CONFIG_PBL2800_ETHER
 - CONFIG_PHY_ICPLUS

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>