u-boot.git/drivers/net/phy/micrel.c, branch v2016.09

net: phy: micrel: add support for KSZ886x switches in MIIM mode

2016-06-21T22:01:52+00:00

This patch adds a phy driver for the Micrel KSZ886x switches.

Similarly to the KSZ8895, SoC MAC is directly connected to the switch
MAC on the switch CPU port, so the link to the switch is always up.

KSZ886x switches can be used in the following configuration modes:
- Unmanaged mode with config stored in external EEPROM
- Managed mode over SPI
- Managed mode over I2C
- Managed mode over mdio/mdc (aka MIIM or SMI)

This patch supports only unmanaged and MIIM modes.

Based on Micrel KSZ886x driver from Linux kernel and
Micrel KSZ8895 driver from U-Boot.

Verified with the KSZ8863MLL.

Signed-off-by: Alexey Firago 
Acked-by: Joe Hershberger

net: phy: Handle phy_startup() error codes properly

2016-05-24T11:17:59+00:00

Propagate error code from genphy_update_link() to phy startup().

Signed-off-by: Michal Simek 
Acked-by: Stephen Warren

drivers: net: phy: micrel: fix build errors with CONFIG_DM_ETH

2016-02-08T15:10:45+00:00

When Micrel phy is selected without CONFIG_PHY_MICREL_KSZ9031 or
CONFIG_PHY_MICREL_KSZ9021 there  is a build error. Fixing this
by adding proper ifdefs

drivers/net/phy/micrel.c:370:39: error: array type has incomplete element type
 static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
                                       ^
drivers/net/phy/micrel.c:372:39: error: array type has incomplete element type
 static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
                                       ^
drivers/net/phy/micrel.c: In function ‘ksz9031_of_config’:
drivers/net/phy/micrel.c:377:23: error: array type has incomplete element type
  struct ksz90x1_ofcfg ofcfg[] = {
                       ^
drivers/net/phy/micrel.c:379:13: error: ‘ksz90x1_rxd_grp’ undeclared (first use in this function)
   { MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW, 2, ksz90x1_rxd_grp, 4 },
             ^
drivers/net/phy/micrel.c:379:13: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/phy/micrel.c:380:13: error: ‘ksz90x1_txd_grp’ undeclared (first use in this function)
   { MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW, 2, ksz90x1_txd_grp, 4 },
             ^
drivers/net/phy/micrel.c:386:3: warning: implicit declaration of function ‘ksz90x1_of_config_group’ [-Wimplicit-function-declaration]
   ret = ksz90x1_of_config_group(phydev, &(ofcfg[i]));
   ^
drivers/net/phy/micrel.c:377:23: warning: unused variable ‘ofcfg’ [-Wunused-variable]
  struct ksz90x1_ofcfg ofcfg[] = {
                       ^
drivers/net/phy/micrel.c: At top level:
drivers/net/phy/micrel.c:370:39: warning: ‘ksz9031_ctl_grp’ defined but not used [-Wunused-variable]
 static const struct ksz90x1_reg_field ksz9031_ctl_grp[] =
                                       ^
drivers/net/phy/micrel.c:372:39: warning: ‘ksz9031_clk_grp’ defined but not used [-Wunused-variable]
 static const struct ksz90x1_reg_field ksz9031_clk_grp[] =
                                       ^
scripts/Makefile.build:277: recipe for target 'drivers/net/phy/micrel.o' failed
make[1]: *** [drivers/net/phy/micrel.o] Error 1
Makefile:1201: recipe for target 'drivers/net/phy' failed
make: *** [drivers/net/phy] Error 2
make: *** Waiting for unfinished jobs....

Signed-off-by: Mugunthan V N 
Reviewed-by: Tom Rini 
Acked-by: Joe Hershberger

net: phy: micrel: fix divisor value for KSZ9031 phy skew

2016-01-28T19:20:30+00:00

The picoseconds to register value divisor(ps_to_regval) should be 60 and not
200. Linux has KSZ9031_PS_TO_REG defined to be 60 as well. 60 is the correct
divisor because the 4-bit skew values are defined from 0x0000(-420ps) to
0xffff(480ps), increments of 60.

For example, a DTS skew value of 420, represents 0ps delay, which should be 0x7.
With the previous divisor of 200, it would result in 0x2, which represents a
-300ps delay.

With this patch, ethernet on the SoCFPGA DE0 Atlas is now able to work with
1Gb ethernet.

References:
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf -> page 26

Signed-off-by: Dinh Nguyen 
Acked-by: Marek Vasut 
Acked-by: Joe Hershberger

net: phy: micrel: Disable B_CAST on config

2016-01-28T19:20:21+00:00

Micrel PHYs KSZ8021/31 and KSZ8081 have a feature where MDIO address 0
is considered as a broadcast address; the PHY will respond even if it
is not its configured (pinstrapped) address. This feature is enabled
by default.

The Linux kernel disables that feature at initialisation, but not
before it probes the MDIO bus. This causes an issue, because a PHY
at address 3 will be discovered at addresses 0 and 3, but will then
only respond at address 3. Because Linux attaches the first PHY it
discovers on 'eth0', it will attach the PHY from address 0, which
will never answer again.

Fix the issue by disabling the broadcast feature in U-Boot, before
Linux is started.

Signed-off-by: Alexandre Messier 
Acked-by: Joe Hershberger

net: phy: micrel: Configure KSZ9021/KSZ9031 skew from OF

2015-12-20T02:36:49+00:00

Add code to process the KSZ9021/KSZ9031 OF props if they are present
and configure skew registers based on the information from the OF.
This code is only enabled if the DM support for ethernet is also
enabled.

Signed-off-by: Marek Vasut 
Cc: Joe Hershberger 
Cc: Chin Liang See 
Cc: Dinh Nguyen 

V2: - Implement struct ksz90x1_reg_field to describe the skew register
      fields more accurately.
    - Fix RXDV/TXEN skew register default value and offset.

net: phy: micrel: disable NAND-tree for KSZ8051

2015-10-29T19:05:48+00:00

NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.

NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.

This patch ensure PHY is not in NAND-tree test mode only for the Micrel
KSZ8051 PHY used by Atmel. There are other Micrel PHY affected but I
doubt they are used on such weird hardware design.

Signed-off-by: Sylvain Rochet 
Acked-by: Joe Hershberger

net: phy: micrel: add support for KSZ8021RNL & KSZ8031RNL

2015-10-29T19:05:46+00:00

This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.

Signed-off-by: Sylvain Lemieux 
Acked-by: Joe Hershberger

net: phy: micrel: add support for KSZ8081MNX

2015-04-20T22:57:12+00:00

This patch adds a support for KSZ8081MNX in MII mode.

Signed-off-by: Luca Ellero 
Acked-by: Pavel Machek

net: phy: micrel: add support for KSZ8895 switch in SMI mode

2015-01-30T21:55:00+00:00

This patch adds a phy driver for the Micrel KSZ8895 switch.  As the SoC MAC
is directly connected to the switch MAC the link to the switch is always up.

But the KSZ8895 switch can be hardwired in three configuration modes :
- not configurable with eventually an eeprom-stored configuration
- configurable by the mdio/mdc connection (SMI protocol)
- configurable by a SPI connection.

In not configurable mode, the switch starts automatically, but in the
other modes, it must be started programmatically, by writing 1 in
configuration register 1.
We only support the not configurable and mdio/mdc (aka SMI) modes here.

Signed-off-by: Philippe De Muyter 
Cc: Christian Gmeiner 
Signed-off-by: Joe Hershberger