u-boot.git/drivers/net/phy/phy.c, branch v2013.07-rc3

add support for Xilinx 1000BASE-X phy (GTX)

2013-06-25T00:11:13Z

commit 39695029bc15041c809df3db4ba19bd729c447fa Author: Charles Coldwell Date: Tue Feb 19 08:27:33 2013 -0500 Changes to support the Xilinx 1000BASE-X phy (GTX/MGT) Signed-off-by: Charles Coldwell

net: add ICPlus PHY driver

2013-06-25T00:07:32Z

The driver code was taken from Linux kernel source: drivers/net/phy/icplus.c Signed-off-by: Yegor Yefremov

phy: export genphy_parse_link()

2013-06-25T00:07:32Z

Signed-off-by: Yegor Yefremov

phy: add support for ET1011C phys

2013-05-10T12:25:54Z

Adds an ET1011C PHY driver which is derived from the Linux kernel PHY driver (drivers/net/phy/et1011c.c) from the v3.9-rc2 tag. Note that an errata workaround config option is implemented to allow for TX_CLK to be enabled even when gigabit mode is negotiated. This workaround is used on the PG1.0 TI814X EVM. Signed-off-by: Matt Porter Reviewed-by: Tom Rini

phy: add phy_find_by_mask/phy_connect_dev

2013-01-28T05:57:50Z

It is useful to be able to try a range of possible phy addresses to connect. Also, an ethernet device is not required to use phy_find_by_mask leading to better separation of mii vs ethernet, as suggested by Andy Fleming. Signed-off-by: Troy Kisky

drivers/net/: sparse fixes

2012-11-04T18:00:36Z

phy.c:46:5: warning: symbol 'genphy_config_advert' was not declared. Should it be static? phy.c:121:5: warning: symbol 'genphy_setup_forced' was not declared. Should it be static? phy.c:468:5: warning: symbol 'phy_probe' was not declared. Should it be static? phy.c:491:19: warning: symbol 'get_phy_driver' was not declared. Should it be static? phy.c:508:19: warning: symbol 'phy_device_create' was not declared. Should it be static? phy.c:552:5: warning: symbol 'get_phy_id' was not declared. Should it be static? phy.c:584:19: warning: symbol 'get_phy_device' was not declared. Should it be sta vitesse.c:126:5: warning: symbol 'vsc8601_config' was not declared. Should it be static? vsc7385.c:33:5: warning: symbol 'vsc7385_upload_firmware' was not declared. Should it be static? tgec_phy.c:33:5: warning: symbol 'tgec_mdio_write' was not declared. Should it be static? tgec_phy.c:75:5: warning: symbol 'tgec_mdio_read' was not declared. Should it be static? tgec_phy.c:117:5: warning: symbol 'tgec_mdio_reset' was not declared. Should it be static? eth.c:48:6: warning: symbol 'dtsec_configure_serdes' was not declared. Should it be static? p4080.c:26:5: warning: symbol 'port_to_devdisr' was not declared. Should it be static? Signed-off-by: Kim Phillips

phylib: phy_startup() should return an error code on failure

2012-07-11T18:15:30Z

phy_startup() calls the PHY driver's startup function, but it ignores the return code from that function, and so it never returns any failures. Signed-off-by: Timur Tabi

net: phy: make board_phy_config responsible for calling drv->config

2012-02-27T20:19:25Z

Boards may have things they want done before or after normal phy config. Letting the boards call drv->config allows them more flexibilty. Boards affected by this change are corenet_ds and mpc8544ds. Signed-off-by: Troy Kisky Acked-by: Dirk Behme

phy: Add support for SMSC LAN87xx PHYs

2011-12-05T22:07:59Z

This adds support for the SMSC LAN87xx PHYs. Following PHYs can be used by set CONFIG_PHY_SMSC to config. - SMSC LAN8700 - SMSC LAN8710/LAN8720 - SMSC LAN8710/LAN8720 A setup of PHY was copied from linux kenrel. Signed-off-by: Nobuhiro Iwamatsu Fixed white space errors; modified commit message a bit. Signed-off-by: Wolfgang Denk

Revert "phylib: remove a couple of redundant code lines"

2011-09-28T19:02:43Z

This reverts commit 041c542219af7f31c372d89b4c7c6f4c8064a8ce. The lines removed by this commit weren't redundant. The logic is (and probably should be better commented): Find the intersection of the advertised capabilities of both sides of the link (lpa). From that intersection, find the highest capability we can run at (that will be the negotiated link). Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL). The code will now set phydev->speed to 100, and phydev->duplex to 1, but this link does not support 100FULL. Kudos to Andy Fleming for binging this to attention and for the explanation. Signed-off-by: Wolfgang Denk