u-boot.git/drivers/net/phy/phy.c, branch v2018.09

net: phy: add ofnode node to struct phy_device

2018-07-26T19:08:22+00:00

Now the UCLASS_ETH device "node" field is owerwritten by some network drivers in
case of Ethernet PHYs which are linked to UCLASS_ETH device using
"phy-handle" DT property and when Ethernet PHY driver needs to read some
additional information from DT. In such cases following happens (in
general):

- network drivers
	priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
				   priv->interface);
	<-- phydev is connected to dev which is UCLASS_ETH device

	if (priv->phy_of_handle > 0)
		dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);
	<-- phydev->dev->node is overwritten by phy-handle DT node

- PHY driver in .config() callback
	int node = dev_of_offset(dev);
	<-- PHY driver uses overwritten dev->node
        const void *fdt = gd->fdt_blob;

	 if (fdtdec_get_bool(fdt, node, "property"))
		...

As result, UCLASS_ETH device can't be used any more for DT accessing.

This patch adds additional ofnode node field to struct phy_device which can
be set explicitly by network drivers and used by PHY drivers, so
overwriting can be avoided. Also add helper function phy_get_ofnode()
which will check and return phy_device->node or dev_ofnode(phydev->dev) for
backward compatibility with existing drivers.

Signed-off-by: Grygorii Strashko 
Acked-by: Joe Hershberger

net: phy: Clean up includes of common.h

2018-07-26T19:08:22+00:00

We want to be able to include some other system headers in phy.h but
that requires us to have included common.h in the top-level first.

Also, common.h includes config.h as the first thing it does, so don't
include it directly.

Series-to: u-boot
Series-cc: Grygorii Strashko 
Seried-cc: ti
Series-process-log: sort, uniq
Cover-letter:
Prepare for net: phy: prevent uclass_eth device "node" field overwriting
Prepare for [1] so that it doesn't break the build for a bunch of
boards. There are a number of reasons this series broke the build
but none of them depend on changes in the series, so fix up those
situations ahead of applying that series.

[1] https://patchwork.ozlabs.org/cover/940104/
END
Signed-off-by: Joe Hershberger

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini

phy: Fix style violations

2018-02-26T21:48:55+00:00

Fix some style violations in the generic PHY management code.

Acked-by: Joe Hershberger 
Signed-off-by: Mario Six

net: phy: Add Broadcom BCM53xx switch driver

2018-01-15T18:05:21+00:00

Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.

This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.

Reviewed-by: Stefan Roese 
Signed-off-by: Florian Fainelli

net: phy: Add Amlogic Meson GXL Internal PHY support

2017-11-17T12:44:13+00:00

The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.

The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.

Signed-off-by: Neil Armstrong

net: phy: micrel: Separate KSZ9000 drivers from KSZ8000 drivers

2017-08-07T20:18:30+00:00

The KS8721BL and KSZ9021 PHYs are software-incompatible, yet they
share the same ID. Drivers for bothe PHYs cannot safely coexist, so
the solution was to use #ifdefs to select between the two drivers.

As a result KSZ9031, which has a unique ID, is now caught in the
crossfire. Unless CONFIG_PHY_MICREL_KSZ9031 is defined, the KSZ9031
will not function properly, as some essential configuration code is
ifdef'd-out.

To prevent such situations, move the KSZ9000 drivers to a separate
file, and place them under a separate Kconfig option. While it is
possible to enable both KSZ8000 and KSZ9000 drivers at the same time,
the assumption is that it is highly unlikely for a system to contain
both a KSZ8000 and a KSZ9000 PHY, and that only one of the drivers
will be enabled at any given time.

Signed-off-by: Alexandru Gagniuc 
Reviewed-by: Philipp Tomsich 
Acked-by: Joe Hershberger

dm: core: Replace of_offset with accessor (part 2)

2017-06-01T13:03:04+00:00

At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass

drivers/net/phy: add fixed-phy / fixed-link support

2017-03-26T14:58:26+00:00

This patch adds support for having a "fixed-link" to some other MAC
(like some embedded switch-device).

For this purpose we introduce a new phy-driver, called "Fixed PHY".

Fixed PHY works only with CONFIG_DM_ETH enabled, since the fixed-link is
described with a subnode below ethernet interface.

Most ethernet drivers (unfortunately not all are following same scheme
for searching/attaching phys) are calling "phy_connect(...)" for getting
a phy-device.
At this point we link in, we search here for a subnode called "fixed-
link", once found we start phy_device_create(...) with the special phy-
id PHY_FIXED_ID (0xa5a55a5a).

During init the "Fixed PHY" driver has registered with this id and now
gets probed, during probe we get all the details about fixed-link out of
dts, later on the phy reports this values.

Signed-off-by: Hannes Schmelzer 

Signed-off-by: Hannes Schmelzer 
Acked-by: Joe Hershberger 
Reviewed-by: Christian Gmeiner

net: phy: MSCC Add Support for VSC8530-VSC8531-VSC8540-VSC8541

2017-02-08T22:32:58+00:00

Signed-off-by: John Haechten 
Acked-by: Joe Hershberger