u-boot.git/drivers/net/phy, branch v2012.10

net: Add Vitesse VSC8662 PHY support

2012-09-27T17:21:59+00:00

-VSC8662 is Dual Port 10/100/1000Base-T Phy,
 100Base-FX/1000/Base-X Gigabit Ethernt Transceiver Phy.

-Its register set and features are similar to
 other Vitesse Phys

Signed-off-by: Priyanka Jain 
Signed-off-by: York Sun

net/phy: support the mv88e6352 switch

2012-09-27T17:21:56+00:00

This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.

This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.

Signed-off-by: Valentin Longchamp 
cc: Holger Brunck 
cc: Prafulla Wadaskar 
cc: Joe Hershberger

net: phy: micrel: make ksz9021 phy accessible

2012-07-11T18:15:30+00:00

Micrel accidentally used the same part number
for the KS8721 and KSZ9021. So, both cannot be
in the same build of u-boot. Add a config option
to handle this.

Signed-off-by: Troy Kisky 
Acked-by: Vladimir Zapolskiy

phylib: phy_startup() should return an error code on failure

2012-07-11T18:15:30+00:00

phy_startup() calls the PHY driver's startup function, but it ignores the
return code from that function, and so it never returns any failures.

Signed-off-by: Timur Tabi

net: phy: make board_phy_config responsible for calling drv->config

2012-02-27T20:19:25+00:00

Boards may have things they want done before or after normal phy config.
Letting the boards call drv->config allows them more flexibilty.
Boards affected by this change are corenet_ds and mpc8544ds.

Signed-off-by: Troy Kisky 
Acked-by: Dirk Behme

net: phy: add support for Micrel's KSZ9021

2012-02-27T20:19:25+00:00

Add the gigabit phy KSZ9021.
Also, add function ksz9021_phy_extended_write
/_read for access to the phys extended registers.
The environment variable "disable_giga"
can be used to disable 1000baseTx.

Signed-off-by: Troy Kisky 
Acked-by: Dirk Behme

phy: add Micrel KS8721BL phy definition

2011-12-20T22:50:10+00:00

This adds support for the Micrel KS8721BL/SL PHY.

The definition is taken from the correspondent datasheet.

Signed-off-by: Vladimir Zapolskiy

phy: Add support for SMSC LAN87xx PHYs

2011-12-05T22:07:59+00:00

This adds support for the SMSC LAN87xx PHYs.

Following PHYs can be used by set CONFIG_PHY_SMSC to config.
 - SMSC LAN8700
 - SMSC LAN8710/LAN8720
 - SMSC LAN8710/LAN8720

A setup of PHY was copied from linux kenrel.

Signed-off-by: Nobuhiro Iwamatsu 
Fixed white space errors; modified commit message a bit.
Signed-off-by: Wolfgang Denk

Phy/Marvell: Rewrite the MV88E1111 phy config function based on kernel code

2011-12-05T20:59:00+00:00

The original m88e1111s_config() does not do the SGMII mode
initialization and is buggy. Rewrite the function according to
3.0.6 kernel function m88e1111_config_init() in drivers/net/phy/marvell.c

Signed-off-by: Roy Zang 
Acked-by: Andy Fleming 
Cc: Kumar Gala

powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)

2011-10-20T21:01:37+00:00

The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.

Signed-off-by: Timur Tabi 
Signed-off-by: Kumar Gala