u-boot.git/drivers/net/phy, branch v2012.10-rc1

net: phy: micrel: make ksz9021 phy accessible

2012-07-11T18:15:30Z

Micrel accidentally used the same part number for the KS8721 and KSZ9021. So, both cannot be in the same build of u-boot. Add a config option to handle this. Signed-off-by: Troy Kisky Acked-by: Vladimir Zapolskiy

phylib: phy_startup() should return an error code on failure

2012-07-11T18:15:30Z

phy_startup() calls the PHY driver's startup function, but it ignores the return code from that function, and so it never returns any failures. Signed-off-by: Timur Tabi

net: phy: make board_phy_config responsible for calling drv->config

2012-02-27T20:19:25Z

Boards may have things they want done before or after normal phy config. Letting the boards call drv->config allows them more flexibilty. Boards affected by this change are corenet_ds and mpc8544ds. Signed-off-by: Troy Kisky Acked-by: Dirk Behme

net: phy: add support for Micrel's KSZ9021

2012-02-27T20:19:25Z

Add the gigabit phy KSZ9021. Also, add function ksz9021_phy_extended_write /_read for access to the phys extended registers. The environment variable "disable_giga" can be used to disable 1000baseTx. Signed-off-by: Troy Kisky Acked-by: Dirk Behme

phy: add Micrel KS8721BL phy definition

2011-12-20T22:50:10Z

This adds support for the Micrel KS8721BL/SL PHY. The definition is taken from the correspondent datasheet. Signed-off-by: Vladimir Zapolskiy

phy: Add support for SMSC LAN87xx PHYs

2011-12-05T22:07:59Z

This adds support for the SMSC LAN87xx PHYs. Following PHYs can be used by set CONFIG_PHY_SMSC to config. - SMSC LAN8700 - SMSC LAN8710/LAN8720 - SMSC LAN8710/LAN8720 A setup of PHY was copied from linux kenrel. Signed-off-by: Nobuhiro Iwamatsu Fixed white space errors; modified commit message a bit. Signed-off-by: Wolfgang Denk

Phy/Marvell: Rewrite the MV88E1111 phy config function based on kernel code

2011-12-05T20:59:00Z

The original m88e1111s_config() does not do the SGMII mode initialization and is buggy. Rewrite the function according to 3.0.6 kernel function m88e1111_config_init() in drivers/net/phy/marvell.c Signed-off-by: Roy Zang Acked-by: Andy Fleming Cc: Kumar Gala

powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)

2011-10-20T21:01:37Z

The work-around for P4080 erratum SERDES9 says that the SERDES receiver lanes should be reset after the XAUI starts tranmitting alignment signals. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

phylib: wait for TN2020 to achieve SERDES lane alignment at startup

2011-10-14T04:38:11Z

Before the Teranetics TN2020 PHY can be used, the SERDES lanes need to be aligned, so wait for lane alignment before completing the startup sequence. Note that this process can take up to three seconds. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala

phylib: Work around bug in Teranetics PHY

2011-10-09T22:57:53Z

The Teranetics PHY does not properly report the link state for fiber connections. The new PHY code actually checked the link, and so the FM driver would refuse to talk over a linkless PHY. But the link may actually be up, so now we always report it as up for fiber connections on the tn2020. Signed-off-by: Andy Fleming