VSC8514 QSGMII PHY requires enabling auto-negotiation,
otherwise it wouldn't work.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
  to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
  we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.

Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>

get_phy_id is marked weak but has no protype nor a
strong version, just make it static. Use __weak for
board_phy_config.

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>

In case when several Ethernet ports are supported it's
convenient to see the number of phy that is not found.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>

Old saying says that more than three exclamation marks in a row are
sign of mental disease. Cleanup micrel.c.

Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Acked-by: Chin Liang See <clsee@altera.com>

The following configs are not defined at all:

 - CONFIG_INCA_IP_SWITCH
 - CONFIG_PBL2800_ETHER
 - CONFIG_PHY_ICPLUS

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>

Remove the duplicated argument to || check

Signed-off-by: Maxin B. John <maxin.john@enea.com>

get_phy_id returns -EIO when it can't read from a phy at a given addr.  This would cause
create_phy_by_mask to return prematurely before it had tested the other addresses in the provided mask.

Example usage:
Replace
    phydev = phy_connect(bus, phy_addr, dev, phy_if)
with
    phydev = phy_find_by_mask(bus, phy_mask, phy_if)
    if (phydev)
	phy_connect_dev(phydev, dev);

Signed-off-by: Cormier, Jonathan <jcormier@criticallink.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>