The clock ouput frequency is calculated incorrectly for AR8035 due to
wrong masking of priv->clk_25m_reg and priv->clk_25m_mask.

This same issue has been already fixed in the kernel by:

commit b1f4c209d84057b6d40b939b6e4404854271d797
Author: Oleksij Rempel <o.rempel@pengutronix.de>
Date:   Wed Apr 1 11:57:32 2020 +0200

    net: phy: at803x: fix clock sink configuration on ATH8030 and ATH8035

    The masks in priv->clk_25m_reg and priv->clk_25m_mask are one-bits-set
    for the values that comprise the fields, not zero-bits-set.

    This patch fixes the clock frequency configuration for ATH8030 and
    ATH8035 Atheros PHYs by removing the erroneous "~".

    To reproduce this bug, configure the PHY  with the device tree binding
    "qca,clk-out-frequency" and remove the machine specific PHY fixups.

    Fixes: 2f664823a47021 ("net: phy: at803x: add device tree binding")
    Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
    Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
    Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
    Tested-by: Russell King <rmk+kernel@armlinux.org.uk>
    Signed-off-by: David S. Miller <davem@davemloft.net>

Apply the same fix in the U-Boot driver.

Tested on a i.MX6 Hummingboard.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Tested-by: Tom Rini <trini@konsulko.com>

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>

We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass <sjg@chromium.org>

Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>

Add RX delay enable support for RTL8211F PHY.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>

The two functions are now exactly the same, remove one of them.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

We can configure the clock output in the device tree. Disable the
hardcoded one in here. This is highly board-specific and should have
never been enabled in the PHY driver.

If bisecting shows that this commit breaks your board it probably
depends on the clock output of your Atheros AR8035 PHY. Please have a
look at doc/device-tree-bindings/net/phy/atheros.txt. You need to set
"clk-out-frequency = <125000000>" because that value was the hardcoded
value until this commit.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.

By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.

Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>