u-boot.git/drivers/net/phy, branch v2021.04-rc2

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42Z

Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include at all, so remove that include. Signed-off-by: Simon Glass Signed-off-by: Tom Rini

net: phy: micrel: Try default PHY ofnode first

2021-01-27T15:47:54Z

The phydev structure has a PHY OF node pointer in it, use that OF node first when looking up PHY OF node properties, since that is likely the correct PHY OF node pointer. If the pointer is not valid, which is the case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode. Signed-off-by: Marek Vasut Cc: Joe Hershberger Cc: Ramon Fried

net: phy: ca_phy: Add driver for CAxxxx SoCs

2021-01-27T15:47:47Z

Add phy driver support for MACs embedded inside Cortina Access SoCs Signed-off-by: Abbie Chang Signed-off-by: Alex Nemirovsky CC: Joe Hershberger CC: Tom Rini CC: Aaron Tseng Moved out PHY specific code out of Cortina NI Ethernet driver and into a Cortina Access PHY interface driver

net: phy: micrel: fix typo

2021-01-19T08:11:14Z

Fix typo. Signed-off-by: Claudiu Beznea

net: phy: micrel: add support for DLL setup on ksz9131

2021-01-19T08:11:14Z

Add support for DLL setup on KSZ9131. Signed-off-by: Claudiu Beznea

common: board_r: Drop initr_bbmii wrapper

2021-01-15T19:36:12Z

Add a return value to bb_miiphy_init and use it directly in the post-relocation init sequence, rather than using a wrapper stub. Signed-off-by: Ovidiu Panait Reviewed-by: Simon Glass

drivers/net/phy: Add CORTINA_NO_FW_UPLOAD to Kconfig

2020-12-10T08:26:39Z

Move CORTINA_NO_FW_UPLOAD to Kconfig file so that it can be controlled via defconfig files. Signed-off-by: Meenakshi Aggarwal Reviewed-by: Priyanka Jain

Merge branch 'next'

2020-10-05T18:10:59Z

Bring in the assorted changes that have been staged in the 'next' branch prior to release. Signed-off-by: Tom Rini

net: phy: mscc: sync rx/tx delay settings with Linux on vsc85xx

2020-09-30T20:48:18Z

The Linux kernel does set the clock delays to - 0.2 ns (their default, and lowest, hardware value) if delays should not be enabled - 2.0 ns (which causes the data to be sampled at exactly half way between clock transitions at 1000 Mbps) if delays should be enabled depending on the interface mode See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523 So instead of using arbitrary delay values like now, mimic this behaviour. The behaviour is the same for all of vsc8530/8531/8540/8541 so move that to a shared function while at it. Signed-off-by: Heiko Stuebner Reviewed-by: Philipp Tomsich

net: phy: mscc: make clock-output configurable on vsc85xx

2020-09-30T20:48:18Z

The vsc8530/8531/8540/8541 phys have a configurable clock output that can emit 25, 50 and 125 MHz rates, which in turn may be needed for stable network connections. This follows a similar change introduced into the Linux kernel at https://lore.kernel.org/netdev/20200609133140.1421109-2-heiko@sntech.de Signed-off-by: Heiko Stuebner Reviewed-by: Philipp Tomsich