Update the debug() print, use __func__ to always print matching
function name, and also print bus name in case there are multiple
busses.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>

Replace ifdeffery with plain debug() function call. No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>

The TI DP83822 does have support for configurable RGMII RX/TX clock
shift, add support for parsing DT properties which describe the RX/TX
clock shift configuration and configuration of the matching bits in
RCSR register.

The shift is only configurable on DP83822, the other PHYs supported
by this PHY driver, namely DP83825/DP83826 variants, do not implement
this functionality and the RCSR bits used to configure the clock shift
are missing from those PHYs.

The shift is configurable separately for RX and TX path. Each path can
either enable the shift or disable the shift using single bit. In case
the shift is disabled, a delay of 0ns is added to the path, otherwise
a delay of 3.5ns is added to the path.

Note that the two RCSR bits 11 and 12 have inverted logic, RCSR bit 12
enables RX internal shift when SET, while RCSR bit 11 enables TX shift
when UNSET.

Signed-off-by: Marek Vasut <marex@denx.de>

It seems that every remaining system which enables BITBANGMII also
enables BITBANGMII_MULTI . Remove the BITBANGMII_MULTI symbol and
assume it is always enabled. This allows removal of a bit of legacy
code. No functional change intended.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>

Add driver for Motorcomm YT8521S Gigabit ethernet phy.

Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>

Add driver for Motorcomm YT8531S Gigabit ethernet phy.

Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>

This reverts commit 431be621c6cbc72efd1d45fa36686a682cbb470a.

Section 3.3 of Reduced Gigabit Media Independent Interface (RGMII)
Version 2.0 (4/1/2002) details that a PHYs using a ~2ns internal delay
are referred to as RGMII-ID. This internal delay is optional.

Page 147-148 of the Marvell Doc. No. MV-S107146-U0 Rev. F details
timings of the RX/TX delays. We see that with the TX/RX_CLK delay
enabled, our RX/TX_CTL signal is shifted w.r.t CLK to reflect the delay
added.

In 431be62 there is no timing difference between RGMII and RGMII-ID, and
so programmers wanting to explicitly set their PHY to RGMII will find
that delay added anyway. This could throw off timing if that internal
delay is undesired.

We should be handling all 4 possible RGMII cases of PHY_INTERFACE_MODE:
RGMII, RGMII_ID, RGMII_TXID, and RGMII_RXID. Reverting 431be62
implements this.

See also m88e1111_config_init_rgmii_delays in the equivalent driver in
Linux (drivers/net/phy/marvell.c), which does not set these delays in
RGMII mode.

68e6eca was tested out on an 88E1512 PHY in RGMII-ID mode. This
reversion has been tested by myself on an 88E1518 in RGMII-ID mode. This
patch affects boards using this driver in "rgmii" mode, as the internal
delay will no longer be enabled. Namely kikwood-nsa310s.

Signed-off-by: Rufus Segar <rhs@riseup.net>

Frank Sae <Frank.Sae@motor-comm.com> says:

YT8531 as Gigabit transceiver uses bit15:14(bit9 reserved default 0) as phy
speed mask, YT8821 as 2.5 Gigabit transceiver uses bit9 bit15:14 as phy
speed mask.

Be compatible to YT8821, reform phy speed mask and phy speed macro.

Based on update above, add YT8821 2.5G phy driver.

Link: https://lore.kernel.org/r/20240912120225.28884-1-Frank.Sae@motor-comm.com

Add a driver for the motorcomm YT8821 2.5G ethernet phy which works in
2500base-x mode.

Verify the driver on BPI-R3(with MediaTek MT7986(Filogic 830) SoC) evb.

Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>

YT8531 as Gigabit transceiver uses bit15:14(bit9 reserved default 0) as phy
speed mask, YT8821 as 2.5 Gigabit transceiver uses bit9 bit15:14 as phy
speed mask.

Be compatible to YT8821, reform phy speed mask and phy speed macro.

Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>