u-boot.git/drivers/net/sni_ave.c, branch main

treewide: Remove clk_free

2024-01-30T03:35:02Z

This function is a no-op. Remove it. Signed-off-by: Sean Anderson Link: https://lore.kernel.org/r/20231216193843.2463779-3-seanga2@gmail.com

common: Drop linux/printk.h from common header

2023-09-24T13:54:57Z

This old patch was marked as deferred. Bring it back to life, to continue towards the removal of common.h Move this out of the common header and include it only where needed. Signed-off-by: Simon Glass

net: ave: Switch to new U-Boot PHY API

2023-06-10T11:34:05Z

Use new U-Boot phy_connect() API which also supports fixed PHYs. Signed-off-by: Marek Vasut Reviewed-by: Ramon Fried

net: ave: Add capability of rgmii-id mode

2022-08-08T15:37:57Z

This allows you to specify the type of rgmii-id that will enable phy internal delay in ethernet phy-mode. This adds all RGMII cases to all of get_pinmode() except LD11, because LD11 SoC doesn't support RGMII due to the constraint of the hardware. When RGMII phy mode is specified in the devicetree for LD11, the driver will abort with an error. Signed-off-by: Kunihiko Hayashi Reviewed-by: Ramon Fried

net: phy: don't require PHY interface mode during PHY creation

2022-04-10T05:44:13Z

Currently we require PHY interface mode to be known when finding/creating the PHY - the functions * phy_connect_phy_id() * phy_device_create() * create_phy_by_mask() * search_for_existing_phy() * get_phy_device_by_mask() * phy_find_by_mask() all require the interface parameter, but the only thing done with it is that it is assigned to phydev->interface. This makes it impossible to find a PHY device without overwriting the set mode. Since the interface mode is not used during .probe() and should be used at first in .config(), drop the interface parameter from these functions. Make the default value of phydev->interface (in phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface parameter to phy_connect_dev(), where it should be. Change all occurrences treewide. In occurrences where we don't call phy_connect_dev() for some reason (they only configure the PHY without connecting it to an ethernet controller), set phydev->interface = value from phy_find_by_mask call. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Vladimir Oltean

treewide: Rename PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA

2022-04-10T05:44:13Z

Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make it compatible with Linux' naming. Signed-off-by: Marek Behún Reviewed-by: Stefan Roese Reviewed-by: Ramon Fried Reviewed-by: Vladimir Oltean

net: introduce helpers to get PHY interface mode from a device/ofnode

2022-04-10T05:44:12Z

Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the "phy-mode" / "phy-connection-type" property. Add corresponding UT test. Use them treewide. This allows us to inline the phy_get_interface_by_name() into ofnode_read_phy_mode(), since the former is not used anymore. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Tested-by: Patrice Chotard

common: Drop asm/global_data.h from common header

2021-02-02T20:33:42Z

Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include at all, so remove that include. Signed-off-by: Simon Glass Signed-off-by: Tom Rini

dm: treewide: Rename ofdata_to_platdata() to of_to_plat()

2020-12-13T23:51:09Z

This name is far too long. Rename it to remove the 'data' bits. This makes it consistent with the platdata->plat rename. Signed-off-by: Simon Glass

dm: treewide: Rename dev_get_platdata() to dev_get_plat()

2020-12-13T23:51:09Z

Rename this to be consistent with the change from 'platdata'. Signed-off-by: Simon Glass