u-boot.git/drivers/net/ti, branch v2025.01

drivers: net: Remove duplicate newlines

2024-07-22T16:53:05Z

Drop all duplicate newlines. No functional change. Signed-off-by: Marek Vasut

Restore patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"

2024-05-20T19:35:03Z

As part of bringing the master branch back in to next, we need to allow for all of these changes to exist here. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

Merge tag 'v2024.07-rc3' into next

2024-05-20T16:16:33Z

Prepare v2024.07-rc3

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

2024-05-19T14:16:36Z

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"' I failed to notice that b4 noticed it was based on next and so took that as the base commit and merged that part of next to master. This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

net: ti: am65-cpsw-nuss: fix error handling for "RX dma add buf failed"

2024-05-15T16:46:47Z

The RX DMA channel has been requested at this point already, so it must be freed. Signed-off-by: Matthias Schiffer

net: ti: am65-cpsw-nuss: avoid errors due to imbalanced start()/stop()

2024-05-15T16:46:47Z

The eth-uclass state machine doesn't prevent imbalanced start()/stop() calls - to the contrary, it even provides eth_init_state_only() and eth_halt_state_only() functions that change the state without any calls into the driver. This means that the driver must be robust against duplicate start() and stop() calls as well as send/recv calls while the interface is down. We decide not to print error messages but just to return an error in the latter case, as trying to send packets on a disabled interface commonly happens when the netconsole is still active after the Ethernet has been halted during bootm. Signed-off-by: Matthias Schiffer

net: Remove and add needed includes

2024-05-07T14:00:55Z

Remove from this driver directory and when needed add missing include files directly. Signed-off-by: Tom Rini

Merge patch series "Introduce ICSSG Ethernet driver"

2024-04-12T19:59:12Z

MD Danish Anwar says: Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI AM654 SR2.0. The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces support for ICSSG driver in uboot. This series has been tested on AM65x SR2.0, and the ICSSG interface is able to ping / dhcp and boot kernel using tftp in uboot. To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC cores and RPROC cores need to be booted with the firmware. This step is done inside driver similar to kernel. The remoteproc driver uses request_fw_into_buf() API from fs-loader driver to load and start rproc with the required firmwares. This series only introduces driver files. The device tree and config changes to enable ICSSG driver will be introduced later.

net: ti: icssg: Add support sending FDB command to update rx_flow_id

2024-04-12T19:54:43Z

ICSSG firmware supports FDB commands. Add support to send FDB commands from driver. Once rx_flow_id is obtained from dma, let firmware know that we are using this rx_flow_id by sending a FDB command. Reviewed-by: Ravi Gunasekaran Signed-off-by: MD Danish Anwar

net: ti: icssg: Add ICSSG ethernet driver

2024-04-12T19:54:43Z

This is the PRUSS Ethernet driver for TI AM654 SR2.0 and later SoCs with the ICSSG PRU Sub-system running EMAC firmware. ICSSG Subsystem supports two slices per instance. This driver caters to both slices / ports of the icssg subsystem. Since it is not possible for Ethernet driver to register more than one port for a given instance, this patch introduces top level PRUETH as UCLASS_MISC and binds UCLASS_ETH to individual ports in order to support bringing up more than one Ethernet interface in U-Boot. Since top level driver is UCLASS_MISC, board files would need to instantiate the driver explicitly. Signed-off-by: MD Danish Anwar Reviewed-by: Ravi Gunasekaran