u-boot.git/drivers/net/ti, branch v2025.07

net: ti: am65-cpsw-nuss: invoke phy_config() in driver's .start callback

2025-04-28T19:24:56Z

Currently, the phy_config() API is invoked by the driver only once since it has been probed. While this works in general, it doesn't allow the driver to bring the PHY back to its default reset state. As a result, the driver might not be able to recover the PHY from a bad state. To address this, move phy_config() into the driver's start callback (am65_cpsw_start()). Apart from providing the means to recover the PHY in the event of failure, the implementation is in line with the idea of "reset and configure" that is already followed by am65_cpsw_start() when it comes to programming the CPSW MAC. Signed-off-by: Siddharth Vadapalli

net: am65-cpsw: cpsw_mdio: fix typo in error message

2025-03-31T23:04:20Z

Replace "froced" by "forced" Signed-off-by: Richard Genoud

drivers: net: Remove duplicate newlines

2024-07-22T16:53:05Z

Drop all duplicate newlines. No functional change. Signed-off-by: Marek Vasut

Restore patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"

2024-05-20T19:35:03Z

As part of bringing the master branch back in to next, we need to allow for all of these changes to exist here. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

Merge tag 'v2024.07-rc3' into next

2024-05-20T16:16:33Z

Prepare v2024.07-rc3

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

2024-05-19T14:16:36Z

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"' I failed to notice that b4 noticed it was based on next and so took that as the base commit and merged that part of next to master. This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35. Reported-by: Jonas Karlman Signed-off-by: Tom Rini

net: ti: am65-cpsw-nuss: fix error handling for "RX dma add buf failed"

2024-05-15T16:46:47Z

The RX DMA channel has been requested at this point already, so it must be freed. Signed-off-by: Matthias Schiffer

net: ti: am65-cpsw-nuss: avoid errors due to imbalanced start()/stop()

2024-05-15T16:46:47Z

The eth-uclass state machine doesn't prevent imbalanced start()/stop() calls - to the contrary, it even provides eth_init_state_only() and eth_halt_state_only() functions that change the state without any calls into the driver. This means that the driver must be robust against duplicate start() and stop() calls as well as send/recv calls while the interface is down. We decide not to print error messages but just to return an error in the latter case, as trying to send packets on a disabled interface commonly happens when the netconsole is still active after the Ethernet has been halted during bootm. Signed-off-by: Matthias Schiffer

net: Remove and add needed includes

2024-05-07T14:00:55Z

Remove from this driver directory and when needed add missing include files directly. Signed-off-by: Tom Rini

Merge patch series "Introduce ICSSG Ethernet driver"

2024-04-12T19:59:12Z

MD Danish Anwar says: Introduce ICSSG PRUETH support in uboot. The ICSSG driver is used in TI AM654 SR2.0. The ICSSG PRU Sub-system runs on EMAC firmware. This series Introduces support for ICSSG driver in uboot. This series has been tested on AM65x SR2.0, and the ICSSG interface is able to ping / dhcp and boot kernel using tftp in uboot. To use ICSSG2 ethernet, the ICSSG firmware needs to be loaded to PRU RPROC cores and RPROC cores need to be booted with the firmware. This step is done inside driver similar to kernel. The remoteproc driver uses request_fw_into_buf() API from fs-loader driver to load and start rproc with the required firmwares. This series only introduces driver files. The device tree and config changes to enable ICSSG driver will be introduced later.