u-boot.git/drivers/net, branch v2009.08

tsec: Wait for auto-negotiation to complete without link

2009-08-21T17:35:30+00:00

Previously, waiting for auto-negotiation would only occur if a valid
link had been detected.  Problems arose when attempting to use a
tsec immediately after bootup but before link was achieved, eg:
=> dhcp
Auto-neg error, defaulting to 10BT/HD
eTSEC1: No link.
Auto-neg error, defaulting to 10BT/HD
eTSEC2: No link.
=>

With this patch applied the same operation as above resulted in:
=> dhcp
Waiting for PHY auto negotiation to complete. done
Enet starting in 1000BT/FD
Speed: 1000, full duplex

Signed-off-by: Peter Tyser 
Signed-off-by: Ben Warren

arm: kirkwood: See to it that sent data is 8-byte aligned

2009-08-21T16:57:33+00:00

U-boot might use non-8-byte-aligned addresses for sending data, which
the kwgbe_send doesn't accept (bootp does this for me). This patch
copies the data to be sent to a malloced temporary buffer if it is
non-aligned.

Signed-off-by: Simon Kagstrom 
Signed-off-by: Ben Warren

Wait for the link to come up on kirkwood network init

2009-08-21T16:57:33+00:00

This patch makes the device wait for up to 5 seconds for the link to
come up, similar to what many of the other network drivers do. This
avoids confusing situations where, e.g., a tftp fails when initiated
early after U-boot has started (before the link has come up).

Signed-off-by: Simon Kagstrom 
Signed-off-by: Ben Warren

arm:kirkwood Define kirkwood phy address magic number

2009-08-21T16:57:33+00:00

Signed-off-by: Simon Kagstrom 
Signed-off-by: Ben Warren

e1000: fix PCI memory addressing

2009-08-21T16:57:33+00:00

The Intel E1000 driver was making assumptions about the relationship between
some virtual, physical, and PCI addresses.

Also fix some bad usage of the DEBUGOUT macro

Signed-off-by: Timur Tabi 
Acked-by: Kumar Gala 
Signed-off-by: Ben Warren

net: kirkwood: updates: used eth_setenv_enetaddr api

2009-08-10T21:58:13+00:00

eth_setenv_enetaddr is avaible by upper layer
using this saves 204 bytes on total image size

used Local OUI instead of Marvell OUI for
random MAC address generation logic

Signed-off-by: Prafulla Wadaskar 
Signed-off-by: Ben Warren

Fix E1000 build warning on AP1000 board

2009-08-10T21:53:54+00:00

 Fix E1000 build warning on AP1000 board
 Fix the build warning on AP1000 board:
 e1000.c:131: warning: 'e1000_read_eeprom' used but never defined
 e1000.c:2012: warning: 'e1000_set_phy_mode' defined but not used

Signed-off-by: Roy Zang 
Signed-off-by: Ben Warren

net: phy: bugfixes: mv88E61xx compiler warnings fixed

2009-08-10T21:53:52+00:00

1. mv88E61xx driver compiler warnings fixed
2. idstr if-else statements changed to switch() construct
   and added default case too.
   This fixed idstr may be uninitialized warning

Signed-off-by: Prafulla Wadaskar 
Signed-off-by: Ben Warren

arm: A320: driver for FTMAC100 ethernet controller

2009-08-10T21:53:52+00:00

This patch adds an FTMAC100 ethernet driver for Faraday A320 evaluation board.

Signed-off-by: Po-Yu Chuang 
Signed-off-by: Ben Warren

Dual-license IBM code contributions

2009-08-09T21:15:33+00:00

It was brought to our attention that U-Boot contains code derived from the
IBM OpenBIOS source code originally provided with some of the older PowerPC
4xx development boards.  As a result, the original license of this code has
been carried in the various files for a number of years in the U-Boot project.

IBM is dual-licensing the IBM code contributions already present in U-Boot
under either the terms of the GNU General Public License version 2, or the
original code license already present.

Signed-off-by: Josh Boyer