u-boot.git/drivers/net, branch v2011.03-rc1

DaVinci DM6467: Added ET1011C (LSI) PHY support

2011-02-01T23:54:44+00:00

Added arch/arm/cpu/arm926ejs/davinci/et1011c.c for handling
ET1011C gigabit phy. which overrides get_link_speed function
from default implementation. This enables output of 125 MHz
reference clock on SYS_CLK pin.

Signed-off-by: Prakash PM 
Signed-off-by: Sandeep Paulraj

DaVinci EMAC: Add name to Ethernet device

2011-02-01T23:54:44+00:00

Adds "DaVinci-EMAC" as the name of the device so that
it gets printed as "Using DaVinci-EMAC device"
during network access (dhcp, tftp) instead of empty name
in "Using" statement.This name also gets
reflected in 'ethact' env variable.


Signed-off-by: Hemant Pedanekar 
Signed-off-by: Sandeep Paulraj

DaVinci EMAC: Fix davinci_eth_gigabit_enable

2011-02-01T23:54:44+00:00

Enabling the gigabit was overwriting the
previous configuration by setting up only GIGAFORCE and
GIG bits of MAC control register.
Modified to retain previous configuration while
gigabit enabling.

Signed-off-by: Prakash PM 
Signed-off-by: Sandeep Paulraj

fec_mxc: add support for MX53 processor

2011-02-01T23:54:41+00:00

This patch add FEC support for Freescale MX53 processor

Signed-off-by: Jason Liu

NET: lan91c96: Correct chip detect logic

2011-01-18T22:58:35+00:00

The lan91c96_detect_chip routine is not correct according
to the manual.

Signed-off-by: YanJun Yang

LAN91C*: Change chip names to fit the eth_device struct size

2011-01-10T21:38:36+00:00

The eth_device.name field length is limited by NAMESIZE,
which is 16 defined in include/net.h. Unfortunately, two
of the names in lan91c96.c are beyond that.

Signed-off-by: YanJun Yang

ftgmac100: support of gigabit eth ftgmac100

2011-01-09T21:16:51+00:00

Add Faraday's ftgmac100 (gigabit ethernet)
MAC controller's driver.

Signed-off-by: Macpaul Lin

miiphy: convert to linux/mii.h

2011-01-09T17:06:50+00:00

The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.

Signed-off-by: Mike Frysinger

Merge branch 'master' of ../master into next

2010-12-16T22:00:53+00:00

tsec: Revert to setting TBICR_ANEG_ENABLE by default for SGMII

2010-12-13T15:32:15+00:00

The following commit:

commit 46e91674fb4b6d06c6a4984c0b5ac7d9a16923f4
Author: Peter Tyser 
Date:   Tue Nov 3 17:52:07 2009 -0600

    tsec: Force TBI PHY to 1000Mbps full duplex in SGMII mode

Removed setting Auto-Neg by default, however this is believed to be
proper default configuration for initialization of the TBI interface.

Instead we explicitly set CONFIG_TSEC_TBICR_SETTINGS for the
XPedite5370 & XPedite5500 boards that use a Broadcomm PHY which require
Auto-Neg to be disabled to function properly.

This addresses a breakage on the P2020 DS & MPC8572 DS boards when used
with an SGMII riser card.  We also remove setting
CONFIG_TSEC_TBICR_SETTINGS on the P1_P2_RDB family of boards as now the
default setting is sufficient for them.

Additionally, we clean up the code a bit to remove an unnecessary second
define.

Signed-off-by: Kumar Gala 
Acked-by: Peter Tyser 
Tested-by: Peter Tyser