u-boot.git/drivers/net, branch v2011.09

Revert "phylib: remove a couple of redundant code lines"

2011-09-28T19:02:43+00:00

This reverts commit 041c542219af7f31c372d89b4c7c6f4c8064a8ce.

The lines removed by this commit weren't redundant. The logic is (and
probably should be better commented):

Find the intersection of the advertised capabilities of both sides of
the link (lpa).
From that intersection, find the highest capability we can run at
(that will be the negotiated link).

Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL).

The code will now set phydev->speed to 100, and phydev->duplex to 1,
but this link does not support 100FULL.

Kudos to Andy Fleming  for binging this to
attention and for the explanation.

Signed-off-by: Wolfgang Denk

KS8695: convert KS8695 eth driver to CONFIG_MULTI_ETH

2011-09-10T14:10:34+00:00

Trivial conversion of the ks8695eth driver to a CONFIG_MULTI_ETH type
driver.

Signed-off-by: Greg Ungerer

phylib: remove a couple of redundant code lines

2011-09-09T22:08:26+00:00

This change slightly improves readability of the phydev speed/duplex
assignment logic.

Signed-off-by: Vladimir Zapolskiy 
Acked-by: Detlev Zundel

phylib: reset mii bus only if reset handler is registered

2011-09-09T22:07:55+00:00

This change allows to cope with a mii bus device registered using
miiphy_register(), which doesn't assign a default reset handler.

Signed-off-by: Vladimir Zapolskiy 
Acked-by: Detlev Zundel

smc911x: Fix build warnings

2011-09-09T21:57:24+00:00

Commit 6af1d41 "smc911x MII made available" was missing a few "const"
qualifiers.  Fix the resulting in build warnings:

smc911x.c: In function 'smc911x_initialize':
smc911x.c:297: warning: passing argument 2 of 'miiphy_register' from incompatible pointer type
smc911x.c:297: warning: passing argument 3 of 'miiphy_register' from incompatible pointer type

Signed-off-by: Wolfgang Denk 
Cc: Helmut Raiger

smc911x MII made available

2011-09-07T21:49:58+00:00

The driver already had the MII functions, but they have not been
registered using miiphy_register().

Signed-off-by: Helmut Raiger

da850: fix the channel number for EMAC teardown init

2011-09-04T09:36:19+00:00

TX and RX channel numbers programmed as '1' during EMAC
teardown initialization is wrong. This patch fixes the
same by setting channel number to '0' which is used by U-boot.

Signed-off-by: Sugumar Natarajan 
Signed-off-by: Nagabhushana Netagunte 
Signed-off-by: Sandeep Paulraj

phy.c: make less verbose - turn printf() into debug()

2011-08-31T20:35:27+00:00

The PHY driver was too verbose and corrupted the boot message display
like this:

	...
	Net:   TSEC0 connected to Marvell 88E1111S
	TSEC1 connected to Marvell 88E1111S
	TSEC0, TSEC1
	...

Turn printf() into debug() so we het the expected output again:

	...
	Net:   TSEC0, TSEC1
	...

Signed-off-by: Wolfgang Denk 
Cc: Kumar Gala

Add Ethernet hardware MAC address framework to usbnet

2011-08-08T19:05:23+00:00

Built-in Ethernet adapters support setting the mac address by means of a
ethaddr environment variable for each interface (ethaddr, eth1addr, eth2addr).

This adds similar support to the USB network side, using the names
usbethaddr, usbeth1addr, etc. They are kept separate since we don't want
a USB device taking the MAC address of a built-in device or vice versa.

Signed-off-by: Simon Glass 
Tested-by: Eric Bénard

Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx

2011-08-02T19:52:21+00:00

* 'master' of git://git.denx.de/u-boot-ppc4xx:
  net/4xx: Install interrupt handler after driver registration