u-boot.git/drivers/net, branch v2015.01-rc4

net/fm: update ft_fixup_port to differentiate dual-role mac

2014-12-15T17:15:55Z

we need to differentiate dual-role MACs into two types: MACs with 10GEC enumeration consistent with DTSEC enumeration(defined by CONFIG_FSL_FM_10GEC_REGULAR_NOTATION) and other MACs without CONFIG_FSL_FM_10GEC_REGULAR_NOTATION defined. Signed-off-by: Shengzhou Liu Reviewed-by: York Sun

net/phy: enable serdes auto-negotiation for vsc8514 phy

2014-12-05T16:06:15Z

VSC8514 QSGMII PHY requires enabling auto-negotiation, otherwise it wouldn't work. Signed-off-by: Shengzhou Liu Reviewed-by: York Sun

net/fman: update 10GEC to fit new SoC

2014-12-05T16:06:15Z

fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER. but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs. on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below: 10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2 on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below: 10GEC1->MAC1, 10GEC2->MAC2 so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on which 10GEC enumeration is consistent with MAC enumeration. Signed-off-by: Shengzhou Liu Reviewed-by: York Sun

powerpc/mpc85xx: Add T1024/T1023 SoC support

2014-12-05T16:06:14Z

Add support for Freescale T1024/T1023 SoC. The T1024 SoC includes the following function and features: - Two 64-bit Power architecture e5500 cores, up to 1.4GHz - private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC) - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration - Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI) - High-speed peripheral interfaces - Three PCI Express 2.0 controllers - Additional peripheral interfaces - One SATA 2.0 controller - Two USB 2.0 controllers with integrated PHY - Enhanced secure digital host controller (SD/eSDHC/eMMC) - Enhanced serial peripheral interface (eSPI) - Four I2C controllers - Four 2-pin UARTs or two 4-pin UARTs - Integrated Flash Controller supporting NAND and NOR flash - Two 8-channel DMA engines - Multicore programmable interrupt controller (PIC) - LCD interface (DIU) with 12 bit dual data rate - QUICC Engine block supporting TDM, HDLC, and UART - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - Support for hardware virtualization and partitioning enforcement - QorIQ Platform's Trust Architecture 2.0 Differences between T1024 and T1023: Feature T1024 T1023 QUICC Engine: yes no DIU: yes no Deep Sleep: yes no I2C controller: 4 3 DDR: 64-bit 32-bit IFC: 32-bit 28-bit Signed-off-by: Shengzhou Liu Reviewed-by: York Sun

B4860QDS: Enable enet port as per fsl_b4860_serdes2 string in hwconfig

2014-12-05T16:06:14Z

In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp respectively in hwconfig. Signed-off-by: Suresh Gupta Signed-off-by: Shaohui Xie Reviewed-by: York Sun

powerpc/b4860qds: add xfi support

2014-12-05T16:06:13Z

We need following changes to make xfi work on B4: 1. set cross-point switch VSC3308 to use sfp config when running xfi; 2. add 10G interface check for xfi; 3. set phy address for xfi so the 10G ports can be registered by mdio; Signed-off-by: Shaohui Xie Reviewed-by: York Sun

net/phy: Add support for CS4315/CS4340 PHY

2014-12-05T16:06:11Z

Add support for Cortina CS4315/CS4340 10G PHY. - This driver loads CS43xx firmware from NOR/NAND/SPI/SD device to initialize Cortina PHY. - Cortina PHY has non-standard offset of PHY ID registers, thus we define own get_phy_id() to override default get_phy_id(). - To define macro CONFIG_PHY_CORTINA will enable this driver. Signed-off-by: Shengzhou Liu Reviewed-by: York Sun

Freescale t104x: Do not exclude SGMII

2014-12-05T16:06:07Z

fman_port_enet_if() tests if FM1_DTSEC2 or FM1_DTSEC4 uses RGMII or MII and if not returns PHY_INTERFACE_MODE_NONE. This excludes testing for SGMII further down. Remove the unconditional "else return PHY_INTERFACE_MODE_NONE" so SGMII can be tested too. Signed-off-by: Joakim Tjernlund Reviewed-by: York Sun

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

2014-11-26T16:22:29Z

Conflicts: drivers/mmc/fsl_esdhc.c Signed-off-by: Tom Rini

linux/kernel.h: sync min, max, min3, max3 macros with Linux

2014-11-23T11:48:30Z

U-Boot has never cared about the type when we get max/min of two values, but Linux Kernel does. This commit gets min, max, min3, max3 macros synced with the kernel introducing type checks. Many of references of those macros must be fixed to suppress warnings. We have two options: - Use min, max, min3, max3 only when the arguments have the same type (or add casts to the arguments) - Use min_t/max_t instead with the appropriate type for the first argument Signed-off-by: Masahiro Yamada Acked-by: Pavel Machek Acked-by: Lukasz Majewski Tested-by: Lukasz Majewski [trini: Fixup arch/blackfin/lib/string.c] Signed-off-by: Tom Rini