u-boot.git/drivers/net, branch v2016.01-rc4 Unnamed repository; edit this file 'description' to name the repository. net: e1000: use correct helper to do endianness conversion 2016-01-04T17:25:35+00:00 Miao Yan yanmiaobest@gmail.com 2015-12-21T10:07:02+00:00 a40b2dff7bec6c1656a59ce31c16207b8954eb68 In struct e1000_rx_desc, field 'length' is declared as uint16_t, so use le16_to_cpu() to do endianness conversion. Also drop conversion on 'status' which is declared as uint8_t. Signed-off-by: Miao Yan <yanmiaobest@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> 
In struct e1000_rx_desc, field 'length' is declared as
uint16_t, so use le16_to_cpu() to do endianness conversion.

Also drop conversion on 'status' which is declared as
uint8_t.

Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-03T15:32:24+00:00 Tom Rini trini@konsulko.com 2016-01-03T15:32:24+00:00 f1993ca066100fcaba7d49fecae0ef604e5807e2 






net: fec_mxc: unregister mdio bus on probe error
2016-01-03T14:28:06+00:00

Måns Rullgård
mans@mansr.com

2015-12-08T15:38:46+00:00

845a57b4de972aefb21bf7f13b23d472bccb6afb

If fecmxc_initialize_multi() fails, it frees but does not unregister
the mdio bus, causing subsequent uses of the "mii" command to crash.
Fix this by adding mdio_unregister() calls where needed.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>





If fecmxc_initialize_multi() fails, it frees but does not unregister
the mdio bus, causing subsequent uses of the "mii" command to crash.
Fix this by adding mdio_unregister() calls where needed.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>







net: fec_mxc: configure MDIO hold time
2016-01-03T14:26:06+00:00

Måns Rullgård
mans@mansr.com

2015-12-08T15:38:45+00:00

843a3e5893a713a3df752d30d31861d5b03ad75c

If the host clock frequency is higher than 100 MHz, the MDIO hold
time needs to be increased from its current setting of one cycle in
order to meet the specified minium of 10 ns.  Writing an appropriate
value to the HOLDTIME field of the MII_SPEED register achieves this.

Comment copied from Linux kernel.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>





If the host clock frequency is higher than 100 MHz, the MDIO hold
time needs to be increased from its current setting of one cycle in
order to meet the specified minium of 10 ns.  Writing an appropriate
value to the HOLDTIME field of the MII_SPEED register achieves this.

Comment copied from Linux kernel.

Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Eric Nelson <eric@nelint.com>







net: designware: Zap trailing backslash
2015-12-22T03:42:27+00:00

Marek Vasut
marex@denx.de

2015-12-20T02:59:23+00:00

2b2610921920d841bbf0f6b7de2b170aa8cd9598

Trailing backslashes are necessary only in macros, not in the actual
code, so remove them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>





Trailing backslashes are necessary only in macros, not in the actual
code, so remove them.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>







net: eth_designware: select PHYLIB in Kconfig
2015-12-22T03:42:27+00:00

Thomas Chou
thomas@wytron.com.tw

2015-12-07T12:53:29+00:00

25af71c4bfcd54a88cc9098f23416fe9d1f7d80c

Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.

This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>





Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB
from legacy board header files.

This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE
are selected.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Pavel Machek <pavel@denx.de>
Acked-by: Chin Liang See <clsee@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Tested-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>







net: phy: micrel: Configure KSZ9021/KSZ9031 skew from OF
2015-12-20T02:36:49+00:00

Marek Vasut
marex@denx.de

2015-12-05T16:41:58+00:00

22854bda8092babd5a8ac2e64a5bbdc90d7b827f

Add code to process the KSZ9021/KSZ9031 OF props if they are present
and configure skew registers based on the information from the OF.
This code is only enabled if the DM support for ethernet is also
enabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>

V2: - Implement struct ksz90x1_reg_field to describe the skew register
      fields more accurately.
    - Fix RXDV/TXEN skew register default value and offset.





Add code to process the KSZ9021/KSZ9031 OF props if they are present
and configure skew registers based on the information from the OF.
This code is only enabled if the DM support for ethernet is also
enabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>

V2: - Implement struct ksz90x1_reg_field to describe the skew register
      fields more accurately.
    - Fix RXDV/TXEN skew register default value and offset.







net: gem: Add driver dependencies to PHYLIB
2015-12-18T12:15:58+00:00

Michal Simek
michal.simek@xilinx.com

2015-12-11T08:14:31+00:00

7bccc75a2b3f728981920abde4454ba4ea4e481a

Clear driver dependecies via Kconfig. Remove PHYLIB dependency from
the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>





Clear driver dependecies via Kconfig. Remove PHYLIB dependency from
the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>







net: gem: Fix typo in Kconfig entry
2015-12-18T12:15:58+00:00

Michal Simek
michal.simek@xilinx.com

2015-12-09T15:53:52+00:00

c942810787e40504ffe4ce370002e97a2b0adc52

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>





Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>







net: gem: Separate recv and free_pkt functions
2015-12-18T12:15:58+00:00

Michal Simek
michal.simek@xilinx.com

2015-12-09T13:26:48+00:00

9d9211ac11796898a12cc74b79302b08b5a6db93

Use core to call net_process_received_packet() instead of call inside
the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>





Use core to call net_process_received_packet() instead of call inside
the driver.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>