u-boot.git/drivers/net, branch v2016.07-rc3

net: phy: marvell: Do not reset 88e1310 after autoneg

2016-06-21T22:01:52Z

Commit a058052c "net: phy: do not read configuration register on reset", changes the behaviour of the phy_reset function such that the state of the BMCR register is not preserved during reset. Change the config function for the m88e1310 so that it does not do a reset after configuring auto-negotiation. Signed-off-by: Nathan Rossi Cc: Joe Hershberger Cc: Michal Simek Cc: Stefan Roese Acked-by: Michal Simek Acked-by: Joe Hershberger Reviewed-by: Stefan Roese

net: phy: micrel: add support for KSZ886x switches in MIIM mode

2016-06-21T22:01:52Z

This patch adds a phy driver for the Micrel KSZ886x switches. Similarly to the KSZ8895, SoC MAC is directly connected to the switch MAC on the switch CPU port, so the link to the switch is always up. KSZ886x switches can be used in the following configuration modes: - Unmanaged mode with config stored in external EEPROM - Managed mode over SPI - Managed mode over I2C - Managed mode over mdio/mdc (aka MIIM or SMI) This patch supports only unmanaged and MIIM modes. Based on Micrel KSZ886x driver from Linux kernel and Micrel KSZ8895 driver from U-Boot. Verified with the KSZ8863MLL. Signed-off-by: Alexey Firago Acked-by: Joe Hershberger

net: rtl8169: fix switching between adapters

2016-06-21T22:01:51Z

The rtl8169 driver uses a global variable to store the register address of the adapter being operated upon. This is updated to point at the correct adapter when sending or receiving a packet, or shutting down the adapter, but not when initializing the adapter. Consequently, switching between different adapters within the same U-Boot runtime does not work correctly since the driver programs the wrong registers during rtl8169_eth_start() -> rtl8169_common_start() -> rtl8169_hw_start(). Note that since rtl8169_eth_stop() does set the global variable, the second consecutive attempt to use the "new" adapter did work even before this patch, because each time network usage is shut down, the network core calls stop, which sets the variable so that the next start does actually initialize the hardware, and the adapter works. Equally, rtl8169_eth_probe() calls rtl_init() which sets the global, so if using only a single device, or if picking the "right" device (based on probe order) when multiple devices are present, ioaddr will already be set correctly from the get-go, so the issue does not occur. Signed-off-by: Stephen Warren Acked-by: Joe Hershberger

Merge branch 'master' of git://git.denx.de/u-boot-atmel

2016-06-13T12:50:58Z

net: macb: Convert to driver model

2016-06-12T21:49:38Z

Add driver-model support to this driver. The old code remains for now so that we can convert boards one at a time. Signed-off-by: Simon Glass Reviewed-by: Heiko Schocher Tested-on: smartweb, corvus, taurus, axm Tested-by: Heiko Schocher Acked-by: Joe Hershberger Reviewed-by: Andreas Bießmann

net: macb: Flush correct cache portion when sending

2016-06-12T21:49:38Z

The end address of the cache flush must be cache-line-aligned since otherwise (at least on ARM926-EJS) the request is ignored. When the cache is enabled this means that packets are not sent. Signed-off-by: Simon Glass Reviewed-by: Heiko Schocher Acked-by: Joe Hershberger Reviewed-by: Andreas Bießmann

net: macb: Prepare for driver-model conversion

2016-06-12T21:49:38Z

Adjust this driver to avoid using struct netdev in functions that driver model will call. Also refactor the receive function to be compatible with driver model. Signed-off-by: Simon Glass Reviewed-by: Heiko Schocher Tested-on: smartweb, corvus, taurus, axm Tested-by: Heiko Schocher Reviewed-by: Joe Hershberger Acked-by: Joe Hershberger Reviewed-by: Andreas Bießmann

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

2016-06-12T16:51:34Z

nand: Embed mtd_info in struct nand_chip

2016-06-04T01:27:48Z

nand_info[] is now an array of pointers, with the actual mtd_info instance embedded in struct nand_chip. This is in preparation for syncing the NAND code with Linux 4.6, which makes the same change to struct nand_chip. It's in a separate commit due to the large amount of changes required to accommodate the change to nand_info[]. Signed-off-by: Scott Wood

net: Add ag7xxx driver for Atheros MIPS

2016-05-31T07:38:11Z

Add ethernet driver for the AR933x and AR934x Atheros MIPS machines. The driver could be easily extended to other WiSoCs. Signed-off-by: Marek Vasut Cc: Daniel Schwierzeck Cc: Joe Hershberger Cc: Wills Wang [fixed Kconfig dependency] Signed-off-by: Daniel Schwierzeck