u-boot.git/drivers/net, branch v2018.05-rc2

net: phy: Don't limit phy addresses by default

2018-04-13T20:56:47+00:00

Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger 
Tested-by: Bin Meng 
Acked-by: Neil Armstrong 
Reviewed-by: Philipp Tomsich

net: sh_eth: Add remaining Gen2 DT compatible

2018-04-13T20:47:52+00:00

Add compatible strings for R8A7790, R8A7793 and R8A7794, since the
contemporary DTs use those don't have a generic match value.

Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu 
Cc: Joe Hershberger 
Acked-by: Joe Hershberger

net: zynq_gem: Use max-speed property from dt

2018-04-13T20:47:48+00:00

Add support to use max-speed property from dt for
determining the supported speed. Use 1000Mbps as
default.

Signed-off-by: Siva Durga Prasad Paladugu 
Signed-off-by: Michal Simek 
Acked-by: Joe Hershberger

net: fec: Fix issue in DM probe timeout

2018-04-13T20:47:39+00:00

Since the probe function has changed to reset FEC controller prior than
setup PHY. If reset FEC controller timeout, the priv->phydev is not
initialized, so can't free it.

Signed-off-by: Ye Li 
Acked-by: Joe Hershberger

net: fex_mxc: add i.MX6UL/SX/SL compatible

2018-04-13T20:47:39+00:00

Add i.MX6UL/SX/SL compatible.

Signed-off-by: Peng Fan 
Acked-by: Joe Hershberger

net: fec: sharing MDIO for two enet controllers

2018-04-13T20:47:38+00:00

On i.MX6SX, 6UL and 7D, there are two enet controllers each has a
MDIO port. But Some boards share one MDIO port for the two enets. So
introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate
the MDIO port for sharing.
In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter
the CONFIG_FEC_MXC_MDIO_BASE.

To i.MX28, adapt to use the new config

Signed-off-by: Peng Fan 
Acked-by: Joe Hershberger 
Cc: Fabio Estevam

net: fec: set dev->seq to priv->dev_id

2018-04-13T20:47:38+00:00

To platforms has two enet interface, using dev->seq could
avoid conflict.

i.MX6UL/ULL evk board net get the wrong MAC address from fuse,
eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the
priv->dev_id to device->seq as the real net interface alias id then
.fec_get_hwaddr() read the related MAC address from fuse.

Signed-off-by: Peng Fan 
Acked-by: Joe Hershberger

net: fec_mxc: simplify fec_get_miibus

2018-04-13T20:47:37+00:00

No need to provide two prototype for this function.
Use ulong for the first parameter, then this function
could be shared for DM/non DM case.

Signed-off-by: Peng Fan 
Acked-by: Joe Hershberger

net: fec_mxc: Fix DM driver issue in recv

2018-04-13T20:47:37+00:00

When using ethernet DM driver, the recv interface has a
change with non-DM interface, that driver needs to set
the packet pointer and provide it to upper layer to process.

In fec driver, the fecmxc_recv functions does not handle the
packet pointer parameter. This may cause crash in upper layer
processing because the packet pointer is not set.

This patch allocates a buffer for the packet pointer and free it
through free_pkt interface.

Signed-off-by: Ye Li 
Reviewed-by: Peng Fan 
Acked-by: Joe Hershberger

net: mvneta: support setting hardware address

2018-04-13T20:47:31+00:00

mvneta already supports setting the MAC address but this was only done
internally when some other part of U-Boot tries to actually use the
interface. This commit exposes this functionality to the ethernet core
code so that the MAC addresses of all interfaces are configured
correctly even if they are not used before loading Linux.

Signed-off-by: Matt Pelland 
Reviewed-by: Stefan Roese 
Acked-by: Joe Hershberger