u-boot.git/drivers/net, branch v2022.07-rc4

net: enetc: unregister mdiobus

2022-06-03T15:15:24Z

If the device fails to probe - for example, when there is no ethaddr set - then the private data is automatically freed but the mdiobus remains registered. Fixes: 1e354cb39314 ("drivers: net: fsl_enetc: register internal MDIO bus") Signed-off-by: Michael Walle

net: e1000: Depend on CONFIG_PCI

2022-05-26T14:32:27Z

This driver depends on PCI. Update the Kconfig accordingly. Signed-off-by: Sean Anderson Reviewed-by: Tim Harvey Reviewed-by: Stefan Roese Reviewed-by: Ramon Fried

spi: spi_flash_probe_bus_cs() rely on DT for spi speed and mode

2022-05-23T13:33:10Z

Now, spi_flash_probe_bus_cs() relies on DT for spi speed and mode and logically calls spi_get_bus_and_cs(). In case spi mode and speed are not read from DT, make usage of spi_flash_probe() instead. To sum-up: - Previous call tree was: spi_flash_probe() -> spi_flash_probe_bus_cs() -> spi_get_bus_and_cs() - Current call tree is: spi_flash_probe() -> _spi_get_bus_and_cs() spi_flash_probe_bus_cs() -> spi_get_bus_and_cs() This patch impacts the following : - cmd/sf.c: if spi mode and/or speed is passed in argument of do_spi_flash_probe(), call spi_flash_probe() otherwise call spi_flash_probe_bus_cs(). - drivers/net/fm/fm.c: as by default spi speed and mode was set to 0 and a comment indicates that speed and mode are read from DT, use spi_flash_probe_bus_cs(). - drivers/net/pfe_eth/pfe_firmware.c: spi speed and mode are not read from DT by all platforms using this driver, so keep legacy and replace spi_flash_probe_bus_cs() by spi_flash_probe(); - drivers/net/sni_netsec.c : spi speed and mode are not read from DT, so replace spi_flash_probe_bus_cs() by spi_flash_probe(). - drivers/usb/gadget/max3420_udc.c: Can't find any platform which make usage of this driver, nevertheless, keep legacy and replace spi_get_bus_and_cs() by _spi_get_bus_and_cs(). - env/sf.c: a comment indicates that speed and mode are read from DT. So use spi_flash_probe_bus_cs(). Signed-off-by: Patrice Chotard Cc: Marek Behun Cc: Jagan Teki Cc: Vignesh R Cc: Joe Hershberger Cc: Ramon Fried Cc: Lukasz Majewski Cc: Marek Vasut Cc: Wolfgang Denk Cc: Simon Glass Cc: Stefan Roese Cc: "Pali Rohár" Cc: Konstantin Porotchkin Cc: Igal Liberman Cc: Bin Meng Cc: Pratyush Yadav Cc: Sean Anderson Cc: Anji J Cc: Biwen Li Cc: Priyanka Jain Cc: Chaitanya Sakinam

net: mvneta: Drop unneeded macro

2022-05-04T05:05:51Z

Macro MVNETA_GMAC_FORCE_LINK_UP can be dropped from value assignment in fixed link case, since it's value is written into the register later in the function for link-down-to-link-up case. The value is written as MVNETA_GMAC_FORCE_LINK_DOWN | MVNETA_GMAC_FORCE_LINK_PASS, and so the macro definition can also be dropped. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Stefan Roese

net: mvneta: Disable fixed PHY code if PHY_FIXED is not compiled in

2022-05-04T05:05:51Z

Guard the code handling the fixed PHY case by CONFIG_IS_ENABLED(PHY_FIXED). Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Stefan Roese

net: mvneta: Drop fixed_link member from private struct

2022-05-04T05:05:51Z

Since this member is checked only at two places drop it and inline it's usage. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Stefan Roese

net: mvneta: Write PHY address just before enabling HW polling

2022-05-04T05:05:51Z

Write PHY address just before enabling HW polling of the PHY. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Stefan Roese

net: mvneta: Convert to use PHY_FIXED for fixed-link

2022-05-04T05:05:51Z

Stop parsing fixed-link in the MAC driver. Instead support only PHY mode and let the fixed PHY driver handle the fixed-link case. Enable CONFIG_PHY_FIXED for mvneta boards that need it: Turris Omnia and ESPRESSObin. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Stefan Roese

net: mvneta: Rename CONFIG_NR_CPUS to MVNETA_NR_CPUS

2022-05-04T05:05:51Z

The CONFIG_* macros are reserved for Kconfig. This was probably done when this driver was being imported from Linux. Rename the macro. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Stefan Roese

net: mvneta: Don't check for CONFIG_PHYLIB

2022-05-04T05:05:51Z

Drop checking for CONFIG_PHYLIB in mvneta, this is already done in Kconfig. Signed-off-by: Marek Behún Reviewed-by: Ramon Fried Reviewed-by: Stefan Roese