Conflicts:
	arch/arm/cpu/arm926ejs/mxs/mxsimage.mx23.cfg
	arch/arm/cpu/arm926ejs/mxs/mxsimage.mx28.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>

Implement a callback to toggle the slot power supply. The callback
can be overriden in case some more complex power supply for the slot
was implemented in hardware, yet for the usual case, one can define
a GPIO which toggles the power to the slot.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Liu Ying <Ying.Liu@freescale.com>

Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>

Add a callback so that a board can implement it's own specific routine to
toggle the port's #PERST line or #define a GPIO to do so.

Signed-off-by: Marek Vasut <marex@denx.de>

The driver is no longer used, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>

Current print only display width of PCIe device. Add print to display
PCIe generation supported by the device.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

Add PCIe driver for the Freescale i.MX6 SoC . This driver operates the
PCIe block in RC mode only, the EP mode is NOT supported. The driver is
tested with the Intel e1000 NIC driver.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

This patch adds support for running on Malta boards using coreFPGA6
core cards, including support for the msc01 system controller used
with them. The system controller is detected at runtime allowing one
U-boot binary to run on a Malta with either.

Due to the PCI I/O base differing between Maltas using gt64120 & msc01
system controllers, the UART setup is modified slightly. A second UART
is added so that there is one pointing at the correct address for each
system controller. The Malta board then defines its own
default_serial_console function to select the correct one at runtime.
The incorrect UART will simply not function.

Tested on:
  - A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both
    with and without an L2 cache.
  - QEMU.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>