u-boot.git/drivers/phy/Makefile, branch v2020.04

phy: mediatek: add MediaTek T-PHY support for PCIe

2019-10-11T14:10:18+00:00

The driver provides PHY for USB2, USB3.0, PCIe and SATA, and now
we just enable PCIe. As for the other functionalities will be
added gradually in upcoming days.

This is adapted from the Linux version.

Tested-by: Frank Wunderlich 
Signed-off-by: Ryder Lee 
Signed-off-by: Frank Wunderlich

phy: add support for AM654x SERDES

2019-08-12T17:33:39+00:00

Add a new SERDES driver for TI's AM654x SoC which configures
the SERDES only for PCIe. Support fo USB3 can be added later.

SERDES in am654x has three input clocks (left input, external
reference clock and right input) and two output clocks (left
output and right output) in addition to a PLL mux clock which
the SERDES uses for Clock Multiplier Unit (CMU refclock).

The PLL mux clock can select from one of the three input
clocks. The right output can select between left input and
external reference clock while the left output can select
between the right input and external reference clock.

The driver has support to select PLL mux and left/right output
mux as specified in device tree.

Signed-off-by: Sekhar Nori

phy: Add support for phy-da8xx-usb

2019-08-08T09:35:02+00:00

In preparation for supporting the musb driver, this patch
adds support for the usb phy associated with the musb driver.

Signed-off-by: Adam Ford

phy: meson: add Amlogic G12A USB2 and USB3+PCIE PHY drivers

2019-05-09T08:38:32+00:00

This adds support for the USB PHYs found in the Amlogic G12A SoC Family.

The USB2 PHY supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.

The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on
the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.

Signed-off-by: Neil Armstrong

phy: Add USB PHY driver for the MT76x8 (7628/7688) SoC

2019-04-12T15:32:53+00:00

This driver is derived from this Linux driver:
linux/drivers/phy/ralink/phy-ralink-usb.c

The driver sets up power and host mode, but also needs to configure PHY
registers for the MT7628 and MT7688.

I removed the reset controller handling for the USB host and device, as
it does not seem to be necessary right now. The soft reset bits for both
devices are enabled by default and testing has shown (with hackish
reset handling added), that USB related commands work identical with
or without the reset handling.

Please note that the resulting USB support is tested only very minimal.
I was able to detect one of my 3 currently available USB sticks.
Perhaps some further work is needed to fully support the EHCI controller
integrated in the MT76x8 SoC.

Signed-off-by: Stefan Roese 
Cc: Marek Vasut 
Cc: Daniel Schwierzeck 
Reviewed-by: Daniel Schwierzeck

PHY: Add phy driver for the keystone USB PHY

2018-12-14T16:59:09+00:00

Signed-off-by: Jean-Jacques Hiblot 
Reviewed-by: Tom Rini

phy: Add a new driver for OMAP's USB2 PHYs

2018-12-07T15:31:46+00:00

This drivers supports the USB2 PHY found on omap5 and dra7 SOCs.

Signed-off-by: Jean-Jacques Hiblot

phy: rcar: Add R-Car Gen3 PHY driver

2018-10-03T10:56:13+00:00

Add a PHY driver for the R-Car Gen3 which allows configuring
USB OTG PHY on Gen3 into host mode and toggles VBUS in case a
dedicated regulator is present.

Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu

phy: db410c: Add MSM USB PHY driver

2018-09-30T17:00:36+00:00

Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.

Signed-off-by: Ramon Fried

phy: rcar: Add R-Car Gen2 PHY driver

2018-08-14T09:31:19+00:00

Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.

Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu