u-boot.git/drivers/phy/Makefile, branch v2022.04 Unnamed repository; edit this file 'description' to name the repository. phy: zynqmp: Add serdes/psgtr driver 2022-01-12T09:41:46+00:00 Michal Simek michal.simek@xilinx.com 2022-01-06T08:49:41+00:00 1d78d68349621316ddff95a0d0d3ab9360061a9a Add PSGTR driver for Xilinx ZynqMP. The most of configurations are taken from Linux kernel psgtr driver. USB3.0 and SGMII configurations are tested on SOM. In SGMII case also IOU_SLCR reg is updated to get proper clock setup and signal detection configuration. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Link: https://lore.kernel.org/r/36e6e9d3baf8511af1916e91e4887032ca2b6c20.1641458978.git.michal.simek@xilinx.com 
Add PSGTR driver for Xilinx ZynqMP.
The most of configurations are taken from Linux kernel psgtr driver.

USB3.0 and SGMII configurations are tested on SOM. In SGMII case also
IOU_SLCR reg is updated to get proper clock setup and signal detection
configuration.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/36e6e9d3baf8511af1916e91e4887032ca2b6c20.1641458978.git.michal.simek@xilinx.com
Merge tag 'ti-v2021.10-rc2' of https://source.denx.de/u-boot/custodians/u-boot-ti 2021-07-29T12:20:06+00:00 Tom Rini trini@konsulko.com 2021-07-29T12:20:06+00:00 38436abd5e58044eccddbcd7ec3610a9104e86b6 - Add MMC High speed modes for AM64 and J7200 - Add Sierra/Torrent SERDES driver - Minor clean-ups for R5F boot from SPL 
- Add MMC High speed modes for AM64 and J7200
- Add Sierra/Torrent SERDES driver
- Minor clean-ups for R5F boot from SPL
Makefile: Move phy rules into drivers/phy 2021-07-28T18:27:54+00:00 Simon Glass sjg@chromium.org 2021-07-11T03:14:23+00:00 9d910b76f70166b7b0b271710a92eaa289b011c6 These don't belong in the drivers Makefile so move them down into the correct place. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Fixup some missing dependencies this exposed] Signed-off-by: Tom Rini <trini@konsulko.com> 
These don't belong in the drivers Makefile so move them down into
the correct place.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup some missing dependencies this exposed]
Signed-off-by: Tom Rini <trini@konsulko.com>
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC 2021-07-27T05:27:12+00:00 Jean-Jacques Hiblot jjhiblot@ti.com 2021-07-21T15:58:38+00:00 1a83f9931e052168c225033d9c642112142dab70 Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES wrapper used to configure some of the input signals to the SERDES. It is used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures three clock selects (pll0, pll1, dig) and supports resets for each of the lanes. This is an adaptation of the linux driver. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com 
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig) and supports resets for each of the
lanes.

This is an adaptation of the linux driver.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com
phy: cadence: Add driver for Sierra PHY 2021-07-27T05:27:12+00:00 Alan Douglas adouglas@cadence.com 2021-07-21T15:58:36+00:00 39b823381d9d27537c032010bdaf005aa60df9a3 Add a Sierra PHY driver with PCIe and USB support. This driver is a port from the mainline linux driver. The PHY has multiple lanes, which can be configured into groups, and a generic PHY device is created for each group. There are two resets controlling the overall PHY block, one to enable the APB interface for programming registers, and another to enable the PHY itself. Additionally there are resets for each PHY lane. The PHY can be configured in hardware to read register settings from ROM, or they can be written by the driver. The sequence of operation on startup is to enable the APB bus, write the PHY registers (if required) for each lane group, and then enable the PHY. Each group of lanes can then be individually controlled using the power_on()/ power_off() function for that generic PHY One difference with the linux driver is that the PHY is always reset after it is powered-on. This is because role switching is not supported in u-boot and the cable orientation is handled by the PHY reset. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Alan Douglas <adouglas@cadence.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210721155849.20994-8-kishon@ti.com 
Add a Sierra PHY driver with PCIe and USB support.
This driver is a port from the mainline linux driver.

The PHY has multiple lanes, which can be configured into
groups, and a generic PHY device is created for each group.

There are two resets controlling the overall PHY block, one
to enable the APB interface for programming registers, and
another to enable the PHY itself.  Additionally there are
resets for each PHY lane.

The PHY can be configured in hardware to read register
settings from ROM, or they can be written by the driver.

The sequence of operation on startup is to enable the APB
bus, write the PHY registers (if required)  for each lane
group, and then enable the PHY.  Each group of lanes
can then be individually controlled using the power_on()/
power_off() function for that generic PHY

One difference with the linux driver is that the PHY is
always reset after it is powered-on. This is because role
switching is not supported in u-boot and the cable
orientation is handled by the PHY reset.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-8-kishon@ti.com
Merge tag 'u-boot-imx-20210717' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx 2021-07-17T14:52:21+00:00 Tom Rini trini@konsulko.com 2021-07-17T14:52:21+00:00 d5dbc661c3041e910e161a95fca9e615d85730ac i.MX ---- - mx7ulp : fix WDOG - imx8 : Phytec - USB3 support for i.MX8 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8277 
i.MX
----

- mx7ulp : fix  WDOG
- imx8 : Phytec
- USB3 support for i.MX8

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/8277
phy: phy-imx8mq-usb: Add USB PHY driver for i.MX8MQ 2021-07-17T11:12:23+00:00 Ye Li ye.li@nxp.com 2021-02-21T16:26:21+00:00 4266dc1dffc173099966d7e2e0cdf959c93800b8 Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Patrick Wildt <patrick@blueri.se> Tested-by: Patrick Wildt <patrick@blueri.se> 
Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
phy: Add driver for ST-Ericsson AB8500 USB PHY 2021-07-14T20:48:15+00:00 Stephan Gerhold stephan@gerhold.net 2021-07-08T18:33:49+00:00 4559df9e8160ae1b78bbfe2e90cda574ffa08317 The AB8500 PMIC contains an USB PHY that needs to be set up in device or host mode to make USB work properly. Add a simple driver for the generic PHY uclass that allows enabling it. The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange. The USB PHY must be configured in either host or device mode and somehow the USB PHY driver must be made aware of the mode. Actually, the MUSB driver used together with this PHY does not support dynamic selection of host/device mode in U-Boot at the moment. Therefore, one very simple approach that works fine is to select the mode to configure at compile time. When the MUSB driver is configured in host mode the PHY is configured in host mode, and similarly when the MUSB driver is configured in device/gadget mode. Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> 
The AB8500 PMIC contains an USB PHY that needs to be set up in
device or host mode to make USB work properly. Add a simple driver
for the generic PHY uclass that allows enabling it.

The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange.
The USB PHY must be configured in either host or device mode and
somehow the USB PHY driver must be made aware of the mode.

Actually, the MUSB driver used together with this PHY does not
support dynamic selection of host/device mode in U-Boot at the moment.
Therefore, one very simple approach that works fine is to select
the mode to configure at compile time. When the MUSB driver is
configured in host mode the PHY is configured in host mode, and
similarly when the MUSB driver is configured in device/gadget mode.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
phy: Add Amlogic AXG MIPI PCIe Analog PHY driver 2021-02-10T09:00:51+00:00 Neil Armstrong narmstrong@baylibre.com 2020-12-29T13:59:01+00:00 4547551aa019698524e809f81f65d5782f62bc1d The Amlogic AXG MIPI + PCIe Analog PHY provides function for both PCIe and MIPI DSI at the same time, and provides the Analog part of MIPI DSI transmission and Analog part of the PCIe lines. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> 
The Amlogic AXG MIPI + PCIe Analog PHY provides function for both PCIe and
MIPI DSI at the same time, and provides the Analog part of MIPI DSI transmission
and Analog part of the PCIe lines.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
phy: Add Amlogic AXG MIPI D-PHY driver 2021-02-10T09:00:51+00:00 Neil Armstrong narmstrong@baylibre.com 2020-12-29T13:59:00+00:00 7ef19503bacf4681a7c8a3025ccbec0944a4b70b The Amlogic AXG SoCs embeds a MIPI D-PHY used to communicate with DSI panels. This D-PHY depends on a separate analog PHY. Signed-off-by:Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> 
The Amlogic AXG SoCs embeds a MIPI D-PHY used to communicate with DSI
panels.

This D-PHY depends on a separate analog PHY.

Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>