Replace instances of http://www.ti.com with https://www.ti.com Signed-off-by: Nishanth Menon <nm@ti.com>
This is merely a dummy driver that makes sure the DWC3 XHCI driver finds its reset and PHY controllers. We rely on iBoot to set up the PHY for us. Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Add Renesas Ethernet SERDES driver for R-Car S4-8 (r8a779f0).
The datasheet describes initialization procedure without any information
about registers' name/bits. So, this is all black magic to initialize
the hardware. Especially, all channels should be initialized at once.
This driver is imported and adjusted from Linux 6.3-rc1 commit:
50133cd3e8dd1 ("phy: renesas: r8a779f0-eth-serdes: Remove retry code in .init()")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
add BMC NPCM750 phy control driver Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Add PSGTR driver for Xilinx ZynqMP. The most of configurations are taken from Linux kernel psgtr driver. USB3.0 and SGMII configurations are tested on SOM. In SGMII case also IOU_SLCR reg is updated to get proper clock setup and signal detection configuration. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org> Link: https://lore.kernel.org/r/36e6e9d3baf8511af1916e91e4887032ca2b6c20.1641458978.git.michal.simek@xilinx.com
- Add MMC High speed modes for AM64 and J7200 - Add Sierra/Torrent SERDES driver - Minor clean-ups for R5F boot from SPL
These don't belong in the drivers Makefile so move them down into the correct place. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Fixup some missing dependencies this exposed] Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES wrapper used to configure some of the input signals to the SERDES. It is used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures three clock selects (pll0, pll1, dig) and supports resets for each of the lanes. This is an adaptation of the linux driver. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210721155849.20994-10-kishon@ti.com
Add a Sierra PHY driver with PCIe and USB support. This driver is a port from the mainline linux driver. The PHY has multiple lanes, which can be configured into groups, and a generic PHY device is created for each group. There are two resets controlling the overall PHY block, one to enable the APB interface for programming registers, and another to enable the PHY itself. Additionally there are resets for each PHY lane. The PHY can be configured in hardware to read register settings from ROM, or they can be written by the driver. The sequence of operation on startup is to enable the APB bus, write the PHY registers (if required) for each lane group, and then enable the PHY. Each group of lanes can then be individually controlled using the power_on()/ power_off() function for that generic PHY One difference with the linux driver is that the PHY is always reset after it is powered-on. This is because role switching is not supported in u-boot and the cable orientation is handled by the PHY reset. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Alan Douglas <adouglas@cadence.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Link: https://lore.kernel.org/r/20210721155849.20994-8-kishon@ti.com