u-boot.git/drivers/phy, branch v2019.01

phy: omap_usb2: Add support for am437x

2018-12-14T16:59:09+00:00

Signed-off-by: Jean-Jacques Hiblot 
Reviewed-by: Tom Rini

PHY: Add phy driver for the keystone USB PHY

2018-12-14T16:59:09+00:00

Signed-off-by: Jean-Jacques Hiblot 
Reviewed-by: Tom Rini

phy: Add a new driver for OMAP's USB2 PHYs

2018-12-07T15:31:46+00:00

This drivers supports the USB2 PHY found on omap5 and dra7 SOCs.

Signed-off-by: Jean-Jacques Hiblot

phy: ti-pip3-phy: Add support for USB3 PHY

2018-12-07T15:31:46+00:00

Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.

Signed-off-by: Vignesh R 

Signed-off-by: Jean-Jacques Hiblot

drivers: cosmetic: Convert SPDX license tags to Linux Kernel style

2018-10-28T13:26:39+00:00

Complete in the drivers directory the work started with
commit 83d290c56fab ("SPDX: Convert all of our single
license tags to Linux Kernel style").

Reviewed-by: Simon Glass 
Signed-off-by: Patrick Delaunay

phy: rcar: Add R-Car Gen3 PHY driver

2018-10-03T10:56:13+00:00

Add a PHY driver for the R-Car Gen3 which allows configuring
USB OTG PHY on Gen3 into host mode and toggles VBUS in case a
dedicated regulator is present.

Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu

phy: db410c: Add MSM USB PHY driver

2018-09-30T17:00:36+00:00

Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.

Signed-off-by: Ramon Fried

phy: marvell: add SATA comphy RX/TX polarity invert support

2018-09-19T11:54:27+00:00

This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.

Signed-off-by: Rabeeh Khoury 
Signed-off-by: Baruch Siach 
Signed-off-by: Stefan Roese

phy: marvell: Support changing SERDES map in board file

2018-09-19T06:59:26+00:00

This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.

This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.

This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.

Signed-off-by: Marek Behun 
Signed-off-by: Stefan Roese

phy: rcar: Add R-Car Gen2 PHY driver

2018-08-14T09:31:19+00:00

Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.

Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu