Using CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y and CONFIG_OF_LIVE=y triggers
a Data Abort exception from unaligned memory access when the pinctrl
driver iterate node properties, e.g. for UART2 on RK3568.
setting mux of GPIO0-24 to 1
setting mux of GPIO0-24 to 1
"Synchronous Abort" handler, esr 0x96000021
elr: 000000000000e554 lr : 000000000000e54c
x 0: 0000000000000a5c x 1: 0000000000000a5c
x 2: 0000000000000007 x 3: 0000000000000065
x 4: 0000000000000007 x 5: 0000000000022d4e
x 6: 0000000000000a7c x 7: 00000000000227a4
x 8: 0000000000021cf0 x 9: 0000000000000a7c
x10: 0000000000021cf0 x11: 0000000000021cf0
x12: 00000000003fda1c x13: 0000000000000007
x14: 00000000003fd9ec x15: 000000000001c0ff
x16: 0000000007000000 x17: 00000000fdccd028
x18: 00000000003fde20 x19: 0000000000000018
x20: 0000000000020670 x21: 0000000000000000
x22: 00000000003fdb00 x23: 00000000003fef90
x24: 0000000000020688 x25: 0000000000000000
x26: 0000000000000001 x27: 00000000003ffc50
x28: 0000000000000000 x29: 00000000003fda60
Code: b94083e1 97ffd508 93407c01 37f81260 (f9401038)
Resetting CPU ...
Fix this by replacing the loop to access node properties with use of
ofnode_for_each_prop instead of the current ifdef.
Also continue to next prop instead of aborting at first sign of an
unknown property.
This fixes the Data Abort exception and also pinconf of e.g. pull and
drive in SPL, e.g. for UART2 on RK3568.
setting mux of GPIO0-24 to 1
setting mux of GPIO0-24 to 1
setting pull of GPIO0-24 to 5
setting mux of GPIO0-25 to 1
setting mux of GPIO0-25 to 1
setting pull of GPIO0-25 to 5
Fixes: e7ae4cf27a6d ("pinctrl: rockchip: Add common rockchip pinctrl driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
AVB[01]_{MAGIC,MDC,MDIO,TXCREFCLK} are registered as both
PINMUX_SINGLE(fn) and PINMUX_IPSR_GPSR(fn) in the pinmux_data array.
The latter are correct, hence remove the former.
Without this fix, the Ethernet PHY is not operational on the MDIO bus.
Ported from Linux kernel commit a145c9a8674ac8fbfa1595276e1b6cbfc5139038 .
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Fixes: 741a7370fc3b8b54 ("pinctrl: renesas: Initial R8A779A0 (V3U) PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6fd217b71e83ba9a8157513ed671a1fa218b23b6.1674824958.git.geert+renesas@glider.be
---
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: LUU HOAI <hoai.luu.ub@renesas.com>
Cc: Marek Vasut <marek.vasut+renesas@mailbox.org>
Move imx8 sci header file to include/firmware/imx, then we could use build macro to reuse some i.MX8 drivers for i.MX9, such as drivers/cpu/imx8_cpu.c. Signed-off-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
Pinctrl/pinconf driver for Renesas RZ/N1 (R906G032) SoC. This is quite rudimentary right now, and only supports applying a default pin configuration as specified by the device tree. Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit dafe0fbfb0f3 ("pinctrl: mediatek: rewrite mtk_pinconf_set and
related functions") changed the logic deciding to set R0 and R1
registers for V1 devices.
Before:
/* Also set PUPD/R0/R1 if the pin has them */
err = mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_PUPD, !pullup);
if (err != -EINVAL) {
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R0, r0);
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R1, r1);
}
After:
/* try pupd_r1_r0 if pullen_pullsel return error */
err = mtk_pinconf_bias_set_pullen_pullsel(dev, pin, disable, pullup,
val);
if (err)
return mtk_pinconf_bias_set_pupd_r1_r0(dev, pin, disable,
pullup, val);
Tracing mtk_pinconf_bias_set_pullen_pullsel shows that the function
always either returns 0 in case of success or -EINVAL in case any error
has occurred. Hence the logic responsible of the decision to program R0
and R1 has been inverted.
This leads to problems on BananaPi R2 (MT7623N) when booting from
SDMMC, it turns out accessing eMMC no longer works since
U-Boot 2022.07:
MT7623> mmc dev 0
Card did not respond to voltage select! : -110
The problem wasn't detected for a long time as both eMMC and SDMMC work
fine if they are used to boot from, and hence R0 and R1 were already
setup by the bootrom and/or preloader.
Fix the logic to restore the originally intended and correct behavior
and also change the descriptive comment accordingly.
Fixes: dafe0fbfb0f3 ("pinctrl: mediatek: rewrite mtk_pinconf_set and related functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
NAND is always at function 2 on port C. Pin lists and mux values were taken from the Linux drivers. Reviewed-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Add rk3588 evb support; - Update pinctrl for rk3568 and rk3588; - Update rk3288 dts; - Update mmc support for rk3568 and rk3588; - Add rng support for rk3588; - Add DSI support for rk3568; - Some other misc fixes in dts, config, driver;
* Add StarFive VisionFive v2 Board support * Support CONFIG_REMAKE_ELF * Code cleanups for RISC-V architecture
IO mux selection is not working correctly for all pins. Sync mux route
data from linux to add any missing and update wrong trigger pins to fix
this. Also apply the pull-up fix needed for GPIO0 D3-D6.
Fixes: 1977d746aa54 ("rockchip: rk3568: add rk3568 pinctrl driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Add support for Rockchip rk3588 variant of pinctrl. The driver is adapted from the Linux driver. Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com> [eugen.hristev@collabora.com: port to latest U-boot, bring more changes from Linux use translated pull values table] Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Tested-by: Jonas Karlman <jonas@kwiboo.se> Reviewed-by: Jonas Karlman <jonas@kwiboo.se>