In rzg2l_pinconf_set and rzg2l_get_pin_muxing if the call to
rzg2l_selector_decode fails then the variable pin may not have been
assigned to. Remove the use of pin from the error message. Also update
the error message to show the invalid selector used instead of port
which will be the error code returned.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Reviewed-by: Paul Barker <paul@pbarker.dev>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>

In zynqmp_pinconf_set if param is PIN_CFG_IOSTANDARD or
PIN_CONFIG_POWER_SOURCE and zynqmp_pm_pinctrl_get_config returns an
error then value will not be assigned to when its value is tested to be
not equal to arg. Add code to only test value not equal to arg if ret is
false.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_misc-v1-4-eeb564a1b032@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>

In zynqmp_pinctrl_prepare_func_groups if called with func->ngroups == 0
then ret will not be assigned to before its value is returned on exit.
Initialise ret to ensure it is always valid.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_misc-v1-3-eeb564a1b032@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>

CI: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/pipelines/27364

Quite a few Smatch issues reported by Andrew, and the LMB allocation
fix.

The driver specifies 154 pins so should have a maximum selector of 153
to ensure that the index into the array special_pins_names does not
overflow.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_qcom-v1-2-42fac6707fd5@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

In sa8775p_get_pin_name the limit check for the index into
msm_special_pins_data allows for more elements than exist. Add code to
ensure the array index remains in bounds.

This issue was found by Smatch.

Signed-off-by: Andrew Goodbody <andrew.goodbody@linaro.org>
Link: https://lore.kernel.org/r/20250807-pinctrl_qcom-v1-1-42fac6707fd5@linaro.org
Signed-off-by: Casey Connolly <casey.connolly@linaro.org>

The name of the pin function was changed last minute in the DT, from
emac0 to gmac0.
Adjust the name we use in the pinctrl driver accordingly.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>

The new DT pinctrl binding would allow us to read the pinmux values from
the DT, but it is actually easier to just continue with hardcoding the
mux values in the driver, and matching them against the "function" name.

Add the values for the primary and secondary pin controller on the A523.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>

The logic was updated without modifying the comment above it

Fixes: 72b8c6d1ebf ("pinctrl: don't fall back to pinctrl_select_state_simple()")

Signed-off-by: Philip Molloy <philip.molloy@analog.com>

The SoC pads of TH1520 are separated into three groups (AP 1, AP 2 and
AON) controlled by independent pin controllers. This patch ports their
driver from Linux kernel with most code for setting pinconf and pinmux
kept as is.

The dt-binding of TH1520 pin controller uses a schema where pins to
configure are specfied as strings and looked up at runtime, which the
generic pinctrl helpers of U-Boot cannot parse, thus a customized
set_state() callback is implemented to parse pinconfig nodes and setup
the configuration.

Signed-off-by: Yao Zi <ziyao@disroot.org>
Acked-by: Leo Yu-Chi Liang <ycliang@andestech.com>