u-boot.git/drivers/power/Kconfig, branch v2016.03

sunxi: power: add support for sy8106a driver

2016-02-23T19:50:07Z

SY8106A is a PMIC which is used on the Allwinner H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is implemented to set the default V-CPU voltage to 1200 mV. This driver is required to ensure the SY8106A V-CPU voltage is set to 1200 mV after a software reset. On cold boot the default SY8106A output voltage is selected to be 1200 mV by a pair of resistors on the Orange Pi PC and Plus. Signed-off-by: Jelle van der Waa Tested-by: Siarhei Siamashka Acked-by: Siarhei Siamashka Signed-off-by: Hans de Goede

sunxi: power: axp818: Enable support for ALDOs

2016-01-26T15:20:05Z

Previously, AXP818 ALDO support was partially added to Kconfig, but never enabled in the board file, nor properly set or configured in Kconfig. The boards continue to work because the AXP818 is designed to pair with the A83T/H8, and the default voltages match the reference design's requirements. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

power: axp818: Add support for DLDO and ELDO regulators

2016-01-26T15:20:05Z

AXP818 provides an array of LDOs to provide power to various peripherals. None of these regulators are critical. Signed-off-by: Chen-Yu Tsai Acked-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: Implement poweroff support for axp221 pmic

2016-01-26T15:20:04Z

Adds poweroff support for axp221 pmic. Signed-off-by: Hans de Goede Acked-by: Ian Campbell

sunxi: Implement poweroff support for axp209 pmic

2016-01-26T15:20:04Z

Adds poweroff support for axp209 pmic. Signed-off-by: Michael van Slingerland Signed-off-by: Hans de Goede Acked-by: Ian Campbell

sunxi: Implement poweroff support for axp152 pmic

2016-01-26T15:20:04Z

Adds poweroff support for axp152 pmic. Signed-off-by: Hans de Goede Acked-by: Ian Campbell

sunxi: power: axp818: add support for axp818 driver

2015-12-10T10:14:22Z

AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board. It's registers are different and calculating reg config is different than that of earlier axp power ICs. DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment. all other voltages can be added subsequently. AXP datasheet is uploaded to wiki: http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf Signed-off-by: Vishnu Patekar Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: Add basic H3 support

2015-11-22T10:30:59Z

Add initial sun8i H3 support, only uart + mmc are supported for now. Signed-off-by: Jens Kuske Reviewed-by: Hans de Goede Signed-off-by: Hans de Goede

sunxi: power: Change axp209 LDO3 and LDO4 default to disabled

2015-10-20T16:40:27Z

LDO3 and LDO4 are normally either unused, or used to power csi attached camera sensors, and as such do not need to be enabled at boot time. Signed-off-by: Hans de Goede Acked-by: Ian Campbell

sunxi: power: Change A23/A33 aldo1 default voltage to 3.0V

2015-10-20T16:40:27Z

On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V, make this the default. Note that this does not cause any functional changes since all sun8i board defconfig-s already contained: CONFIG_AXP_ALDO1_VOLT=3000 . Signed-off-by: Hans de Goede Acked-by: Ian Campbell